To Next Page

To Previous Page

4.7 ANTENNA HEIGHT SETTING (ANTENNA

HEIGHT)

Set the height of radar antenna above sea level.

Do not change this setting carelessly.

Procedures 1. Measure the height of radar antenna above sea level in advance.

2. Open the Serviceman Menu.

3. Perform the following menu open procedure to open the Antenna Height

setting menu.

1. Adjust Menu

→ 4. TXRX Adjustment

→ 1. Antenna Height

4. Select the setting that matches the antenna height measured in step 1.

4-6

All manuals and user guides at all-guides.com

all-guides.com

Table of Contents3
Overview9
Installation of the Scanner11
Selecting the Installation Position12
Installation Procedure18
Connecting the Installation Cable Nke-2103 (Jma-5312-6/6Hs)22
Connecting the Installation Cable Nke-210322
Connecting the Installation Cable Nke-2254 (Jma-5322-7/9/6Hs)24
Connecting the Installation Cable Nke-225424
Connecting the Installation Cable Nke-1130 (Jma-5332-12)26
Connecting the Installation Cable Nke-113026
Installation of the Display Unit29
Selecting the Installation Position30
Installation of the Lcd Monitor31
Installation of the Operation Unit32
Installation of the Power Cable (Cfq-5436)33
Installation of the Cable (Cfq-6912) between the Radar Process Unit and the Scanner35
Connecting to the Gps Receiver37
Connecting to the Gps Compass39
Jlr-20/3041
Other Magnetic Compass42
Connecting to Nmea Heading Output Device43
Connecting to the Gyro and Electromagnetic Log (Gyro I/Funit Setting) (Opton)45
Connecting to the Gyro and Electromagnetic Log45
Connecting to the Pc Plotter50
Connecting to Other Nmea Devices50
Connecting to Other Devices51
Power Supply (Nba-5111) (Option)53
Target Tracking (Nca-877Wa/877A) (Option)54
Plotter Circuit (Ndb-34A) (Option)56
Connecting to Ais (Nqa-2103) (Option)58
Coastline Rom Card/Memory Card (Option)62
Connect Slave Monitor / Vdr65
Interswitch Unit (Nqe-3141-4A/8A) (Option)68
Installation of the Power Control Unit (Nqe-3167) (Option)70
Connection with Nke-2103 (Jma-5312-6/6Hs) / Nke-2254 (Jma-5322-7/9/6Hs) Scanner Units70
3.20.2 Connection with NKE-1130 (JMA-5332-12) Scanner Unit70
Installation of the Power Control Unit70
(Nqe-3167) (Option)70
3.20.3 Connection to Display Unit71
3.20.4 Equipment Cable End Processing71
Installation of the Lan Cable (Option)72
3.21.1 Connection to NDC-1417 RADAR PROCESSOR UNIT73
Network Setting (Network)74
Transmit/Receive Data Setting (Lan Port Setting)76
3.21.4 Equipment Cable End Processing79
Initial Setting85
How to Open the Serviceman Menu86
Tune Adjustment87
Bearing Adjustment89
Range Adjustment89
Navigator Setting (Device)90
Setting of True Bearing Value90
Antenna Height Setting (Antenna Height)91
Setting of Ccrp/Antenna/Gps Antenna Position (Ccrp Setting)92
Setting of Ccrp/Antenna/Gps Antenna Position92
→ 4. CCRP Setting92
Communication Port Setting (Com Port Setting)94
Sector Blank Setting (Sector Blank)97
Tni Blank Setting (Tni Blank)98
Setting of Bearing Pulses from Antenna (Output Pulse)99
Setting of Bearing Pulses from Antenna99
→ 6. Output Pulse99
Slave Mode Setting (Master/Slave)100
Language Setting (Language)101
Date Time Setting101
Main Bang Suppression Adjustment (Mbs)102
Adjustment of Performance Monitor (Mon)103
Magnet Compass Setting104
Gps Receiver Setting105
Dgps Receiver Setting109
Sbas Receiver Setting111
Displaying Gps Reception Status113

Brand	JRC
Model	JMA-5312-6
Category	Marine Radar
Language	English

JRC JMA-5312-6 Installation Manual

Table of Contents

Other manuals for JRC JMA-5312-6

Questions and Answers:

JRC JMA-5312-6 Specifications

Related product manuals