Krone Swadro TC 880 - Technical Data; Technical Specifications

Commissioning
34
Pos: 23.27.1 /Überschr iften/Überschr iften 2/K-O/Kreisel neigung einstellen @ 191\ mod_1381819931154_78. docx @ 1631074 @ 11 @ 1
8.9 Setting the Rotor Inclination
Pos: 23.27.2 /BA/S icherheit/7. Gefahr enhinweise alt/Einste llarbeiten / Einste llungen/Gefahr - E instellarbeiten gezog ene Maschinen @ 224\mod_139 2299165082_78.doc x @ 1817635 @ 2 @ 1
DANGER! - Unexpected machine movement
Effect: Danger to life or serious injuries.
• Only carry out settings when the tractor drive has been switched off and the tractor engine
is idle!
• Switch off the engine
• Remove the ignition key and keep it.
• Secure the machine against the possibility of rolling back.
• Wait until all machine parts have stopped and completely cooled down.
Pos: 23.27.3 /BA/Ei nstellungen/Schwader /Kreiselfahrwerk/ Kreiselneigung ei nstellen Text Einlei tung Swadro TC 680_TC 760 @ 223\ mod_1392114706229_78.doc x @ 1808993 @ 22 @ 1
The rotor pitch angle has been set at a transverse angle to the chassis in the factory. If the
crops are not picked up properly, the working quality can be improved by adjusting the rotor
pitch.
The rotor pitch angle is adjusted for each rotor via the guide wheels at the chassis. The best
results are achieved if the rotor pitch adjustment ensures the tines are closer to the ground level
when outputting the crops than at the start when picking up the crops.
Pos: 23.27.4.1 /Übersc hriften/Übersc hriften 3/K-O/Krei selfahrwerk (Serie) @ 223\mod_1392126168498_78. docx @ 1810305 @ @ 1
8.9.1 Rotor chassis (serial)
Pos: 23.27.4.2 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahrwerk B ild Swadro TC 680_TC 760_TS 620_ TS 680 @ 247\mod_1396424074 075_78.docx @ 1925403 @ 2 @ 1
SW700077_2
I
II
+
1
Fig. 14
Pos: 23.27.4.3 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.doc x @ 1092566 @ 2 @ 1
Pos: 23.27.4.4 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Längsneigung_Krei selfahrwerk (Ser ie) und Tandemfahrwerk_ Mittel- und Seitensch wader @ 247\mod_139642081 3830_78.docx @ 1925162 @ 3 @ 1
Longitudinal inclination:
A change of longitudinal inclination (rotor tilts to the front) is reached if the rear guide wheels
(right and left) of the chassis are reconnected in one of the seven bore holes in the hole pattern.
Pos: 23.27.4.5 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.doc x @ 1092566 @ @ 1
Pos: 23.27.4.6 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselneigu ng einstellen Text Posi tion_Mittel- und Sei tenschwader @ 247\m od_1396419253305_78.doc x @ 1924902 @ 2 @ 1
Setting the rotor inclination:
Pos. I = Reducing rotor inclination
Pos. II = Increasing rotor inclination
Pos: 23.27.4.7 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Vorgehensweise S wadro TC 680_TC 760 @ 223\mod_13921 15608969_78.doc x @ 1809320 @ 3 @ 1
Do not walk beneath the raised rotor.
• Only lift the rotor arms as far as necessary to carry out changes.
• In order to adjust the rotor pitch, disassemble the rear guide wheels and reposition in the
hole pattern.
Pos: 23.27.4.8 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ 2 @ 1