Krone Swadro TC 880 - Selecting Rotor Operation; Rotor Operation with Hydraulic Single-Rotor Lift

Maintenance
78
Pos: 36.22.1 /Überschr iften/Überschr iften 2/P-T/Reifen @ 0\ mod_1197357995667_78. docx @ 18075 @ 22 @ 1
13.7 Tyres
Pos: 36.22.2 /BA/Si cherheit/7. Gefahr enhinweise alt/W arnung - Falsche Reifenmontage @ 0\mod_1197358162433_7 8.docx @ 18132 @ 22222222 @ 1
Warning! - Tyre fitting incorrect
Effect: Injuries or damage to the machine
• Fitting tyres requires sufficient knowledge and the availability of proper tools!
• If tyres are not correctly fitted, it could explode when pumped up. This can cause serious
injury. If you do not have sufficient experience of fitting tyres, have tyres fitted by the
KRONE dealer or a qualified tyre specialist.
• When fitting tyres on the wheel rims, the maximum pressure given by the tyre manufacturer
must not be exceeded. The tyre or even the wheel rim could explode and/or burst.
• If the tyre heels do not fit properly when the maximum permitted pressure is reached, let
out the air, align tyres, lubricate the tyre heels and pump up the tyre again.
• Detailed information about how to fit tyres onto agricultural machinery can be obtained from
the tyre manufacturers.
Pos: 36.22.3 /Überschr iften/Überschr iften 3/P-T/Reifen pr üfen und pflegen @ 0\mod_1197 358037214_78.doc x @ 18094 @ 12212222222222 @ 1
13.7.1 Checking and maintaining tyres
Pos: 36.22.4 /BA/W artung/Reifen/Reihenf olge Bild 6-Loch @ 4\ mod_1213086131413_78.doc x @ 86197 @ 222221 @ 1
1
KS-0-034
6
2
4
5
3
Fig. 52
Pos: 36.22.5 /BA/W artung/Reifen/Reifen pr üfen und pflegen nach W artungstabelle @ 134\mod_1 350480797454_78.d ocx @ 1187905 @ 11 @ 1
When loosening and tightening the wheel nuts, observe the order indicated in the illustration.
Check the wheel nuts: According to the maintenance table
Check the tyre air pressure: According to the maintenance table
Pos: 36.22.6 /BA/W artung/Reifen/Anziehdr ehmoment @ 0\mod_1199 955905460_78.doc x @ 37340 @ 11 @ 1
Tightening Torque
Threading
Key size in
mm
Number of bolts
per hub - pieces
Max. tightening torque
black galvan.
M12 x 1.5 19 4/5 95 Nm 95 Nm
M14 x 1.5 22 5 125 Nm 125 Nm
M18 x 1.5 24 6 290 Nm 320 Nm
M20 x 1.5 27 8 380 Nm 420 Nm
M20 x 1,5 30 8 380 Nm 420 Nm
M22 x 1.5 32 8/10 510 Nm 560 Nm
M22 x 2 32 10 460 Nm 505 Nm
Pos: 36.23 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ 122222 222 @ 1