Krone Swadro TC 880 - With Tandem Chassis Version (Optional)

Commissioning
38
Pos: 23.27.6.1 /Übersc hriften/Übersc hriften 3/A-E/Bei Ausführung Tandemfahrwerk ( optional) @ 223\mod_139 2126673159_78.doc x @ 1810363 @ @ 1
8.9.3 With tandem chassis version (optional)
Pos: 23.27.6.2 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Bild Tandem Swadro TC 680_TC 760_TS 620_TS 680 @ 247\mod _1396423777783_78.doc x @ 1925345 @ @ 1
SW700093
I
II
1
2
III
Fig. 16
Pos: 23.27.6.3 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.doc x @ 1092566 @ 2 @ 1
Pos: 23.27.6.4 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Längsneigung_nac hlaufendes Rad_Mit tel- und Seitenschwad er @ 247\mod_1396366697765 _78.docx @ 1924247 @ @ 1
Longitudinal inclination:
The longitudinal inclination can be changed (rotor tips forward) by reconnecting the rear guide
wheels (right and left) of the chassis in positions I, II and III.
Pos: 23.27.6.5 /Layout Module /----------------Leerzeile 5 Pt.-------------------- @ 120\mod_1342592918145_0.doc x @ 1092566 @ 22 @ 1
Pos: 23.27.6.6 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselneigu ng einstellen Text Posi tion_Mittel- und Sei tenschwader @ 247\m od_1396419253305_78.doc x @ 1924902 @ @ 1
Setting the rotor inclination:
Pos. I = Reducing rotor inclination
Pos. II = Increasing rotor inclination
Pos: 23.27.6.7 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Vorgehensweise S wadro TC 680_TC 760 @ 223\mod_13921 15608969_78.doc x @ 1809320 @ @ 1
Do not walk beneath the raised rotor.
• Only lift the rotor arms as far as necessary to carry out changes.
• In order to adjust the rotor pitch, disassemble the rear guide wheels and reposition in the
hole pattern.
Pos: 23.27.6.8 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Querneigung_TS 620 ( Twin)_TS 680 (Twin)_ TS 740 (Twin) @ 247\mod_139636 6300182_78.docx @ 1924218 @ @ 1
Transverse inclination:
A change of the transverse inclination (to the direction of travel) is reached if one of the rear
guide wheels is set higher or deeper compared to the other guide wheel.
Pos: 23.27.6.9 /Layout Module /----------------Leerzeile-------------------- @ 240\mod_1395147357027_0.doc x @ 1890988 @ @ 1
Pos: 23.27.6.10 /BA/ Einstellungen/Sc hwader/Kreiselfahr werk/Kreiselfahr werk Vorgehensweise Sw adro TC 680_TC 760 @ 223\mod_1392 115608969_78.doc x @ 1809320 @ 22 @ 1
Do not walk beneath the raised rotor.
• Only lift the rotor arms as far as necessary to carry out changes.
• In order to adjust the rotor pitch, disassemble the rear guide wheels and reposition in the
hole pattern.
Pos: 23.27.6.11 /Layout Module /---------------Seitenumbruch------------- --- @ 0\mod_1196175311226_ 0.docx @ 4165 @ @ 1