Safety
8
Pos: 14.1 /Überschri ften/Überschri ften 1/P-T/Sicherhei t @ 0\mod_1195566748646_7 8.docx @ 635 @ 1 @ 1
4 Safety
Pos: 14.2 /Überschri ften/Überschri ften 2/U-Z/Verwendungs zweck @ 1\mod_12017072467 38_78.docx @ 54055 @ 2 @ 1
4.1 Purpose of Use
Pos: 14.3 /BA/Einlei tung/Schwader/Ver wendungszweck Schwad er KAT I und KAT II am Heck. @ 1\mod_120 2129727897_78.doc x @ 57517 @ @ 1
The rotary rake is used for swathing of cut crops. It is attached on the rear in the three-point
block KAT I and KAT II.
Pos: 14.4 /Überschri ften/Überschri ften 2/A-E/Bestimmungs gemäße Verwendung @ 103\m od_1332169199326_78.d ocx @ 940071 @ @ 1
Ver
4.2 Intended use
Pos: 14.5 /BA/Einlei tung/Bestimmungsge mäßer Gebrauch/Schwader /Bestimmungsge mäßer Gebrauch Schwader @ 1\ mod_1202215704310_78.d ocx @ 57818 @ 2 @ 1
The rotary rake is built exclusively for conventionaluse in agricultural work (intended use).
Pos: 14.6 /BA/Einlei tung/Bestimmungsge mäßer Gebrauch/Nicht b estimmungsgemäß @ 103\ mod_1332171672294_78. docx @ 940272 @ @ 1
Unauthorised modifications to the machine may have a negative effect on the machine
characteristics or safe and reliable use of the machine or may interfere with proper operation.
Unauthorised modifications shall therefore release the manufacturer of any liability for
consequential damage.
Pos: 14.7.1 /BA/Si cherheit/Personalqu alifikation und -schul ung @ 0\mod_119563938318 5_78.docx @ 1136 @ @ 1
4.2.1 Personnel Qualification and Training
The machine may be used, maintained and repaired only by persons who are familiar with it
and have been instructed about the dangers connected with it. The operator must define areas
of responsibility and monitoring of personnel. Should personnel lack the required knowledge,
they must receive the required training and instruction. The operator must ensure that the
contents of these operating instructions have been fully understood by personnel.
Repair work not described in these operating instructions should only be performed by
authorised service centres.
Pos: 14.7.2 /BA/Si cherheit/Gefahren bei Nic htbeachtung der Sic herheitshinweise @ 0\ mod_1195639434013_78. docx @ 1155 @ 33 @ 1
4.2.2 Dangers in Case of Non-compliance with the Safety Instructions
Failure to follow the safety instructions could result in personal injury and environmental
hazards as well as damage to the machine. If the safety instructions are not respected, this
could result in the forfeiture of any claims for damages.
Failure to follow the safety instructions could result, for example, in the following hazards:
• Endangering of persons due to not protected working areas.
• Breakdown of important machine functions
• Failure of prescribed methods for repair and maintenance
• Endangering of persons due to mechanical and chemical effects
• Damage to the environment due to leaking hydraulic oil
Pos: 14.7.3 /BA/Si cherheitSicher heitsbewusstes Arbeiten_ Teil1 @ 0\mod_1195639792 576_78.docx @ 1174 @ 33 @ 1
4.2.3 Safety-conscious work practices
Always observe the safety instructions set out in these operating instructions, all existing
accident prevention rules and any internal work, operating and safety rules issued by the
operator.
The safety and accident prevention regulations of the responsible professional associations are
binding.
The safety instructions provided by the vehicle manufacturer should also be observed.
Observe the applicable traffic laws when using public roads.
Be prepared for emergencies. Keep the fire extinguisher and first aid box within reach. Keep
emergency numbers for doctors and fire brigade close to the telephone.
Pos: 14.7.4 /Layout Module ---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.docx @ 4165 @ 3 @ 1
To Next Page
Loading...
