Settings
72
Pos: 33 /Überschrif ten/Überschrif ten 1/A-E/Einstellunge n @ 0\mod_1199868783862_7 8.docx @ 36141 @ 2222 @ 1
12 Settings
Pos: 34.1 /Überschri ften/Überschri ften 2/A-E/Einstellb are Drosseln @ 0\mod_119729 5892260_78.doc x @ 17199 @ 2 @ 1
12.1 Adjustable throttles
Pos: 34.2 /BA/Sic herheit/7. Gefahrenhi nweise alt/Einstel larbeiten / Einstel lungen/Gefahr - Einstel larbeiten gezogene Maschinen @ 224\mod_1392299 165082_78.doc x @ 1817635 @ 2133 @ 1
DANGER! - Unexpected machine movement
Effect: Danger to life or serious injuries.
• Only carry out settings when the tractor drive has been switched off and the tractor engine
is idle!
• Switch off the engine
• Remove the ignition key and keep it.
• Secure the machine against the possibility of rolling back.
• Wait until all machine parts have stopped and completely cooled down.
Pos: 34.3 /BA/Einste llungen/Drossel/ Drosseln einstellen a llgemeiner Text Swadro TC 880_TC 880 X-tr @ 237\mod_13946 26835940_78.doc x @ 1878467 @ 12 @ 1
You can use the adjustable throttles to adjust the lowering speeds of the rotors on the machine.
To allow for different types of tractors and oil pressures, the throttles may need to be
readjusted.
Pos: 34.4 /BA/Einste llungen/Drossel/ Hinweis Einstellung an den D rosseln (Auswir kung) @ 7\mod_12155252237 76_78.docx @ 103417 @ 33 @ 1
Note
Adjustment on the throttles
Even the smallest adjustments to the stud bolts or throttle setting screws may significantly
change the lifting and lowering speed.
Pos: 34.5 /BA/Einste llungen/Drossel/ Hinweis Sechskantmu tter/Imbusschraube kon tern @ 7\mod_121552538 9308_78.docx @ 103437 @ 222 @ 1
Note
Adjustment on the throttles
After an adjustment has been made to the throttles, lock the hexagonal nuts and Allen head
screw. Then test functionality.
Pos: 34.6 /BA/Einste llungen/Drossel/ Drossel Bild Swadro TC 880_ TC 880 X-tr @ 237\mod_1394622 198294_78.doc x @ 1878259 @ 111 @ 1
SW9000047
2
c/d
a/b1
Fig. 49
Pos: 34.7 /BA/Einste llungen/Drossel/ Drossel (1) Aushubgesc hwindigkeit @ 137\mod_1 353510537172_78.doc x @ 1219373 @ 2221112 @ 1
Throttle (1)
Set the speed when extending for swath width adjustment (working width).
• Unscrew the hexagonal nut (a).
• Screw in or screw out the stud bolt (b) (screwing in reduces the flow of oil and thus slows
down the speed when extending for swath width adjustment).
Pos: 34.8 /BA/Einste llungen/Drossel/ Drossel (2) rec hter und linker Kreisel (Mitte lschwader) @ 237\mod_1 394626046565_78.doc x @ 1878438 @ 22222222222 @ 1
Throttle (2)
Set the lowering speed of both rotors.
• Loosen hexagonal socket head screw (c).
• Screw stud bolt (d) in or out (Unscrewing it increases the flow of oil and thus increases the
speed at which the rear rotor is lowered.)
Pos: 35 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0.doc x @ 4165 @ 3333 @ 1
To Next Page
Loading...
