Krone Swadro TS 620 - Connecting Machine to Tractor

Commissioning
54
Pos: 32.10 /Übersc hriften/Überschri ften 2/K-O/MMaschine an den Traktor ankuppeln @ 279\ mod_1405350506791_78. docx @ 2150095 @ 2 @ 1
7.2 Connect the machine to the tractor
Pos: 32.11 /BA/Er stinbetriebnahme/W ender/Siehe Kapitel „I nbetriebnahme“. @ 276\ mod_1404740279247_78. docx @ 2071917 @ @ 1
• See section "Start-up".
Pos: 32.12.1 /Überschr iften/Überschr iften 2/F-J/GGelenk welle @ 0\mod_11997818797 94_78.docx @ 34542 @ 2 @ 1
7.3 PTO shaft
Pos: 32.12.2 /Überschr iften/Überschr iften 3/K-O/LLängenanpa ssung @ 1\mod_120168 7632810_78.docx @ 53589 @ 3 @ 1
7.3.1 Length adjustment
Pos: 32.12.3 /BA/Er stinbetriebnahme/ Gelenkwelle/Trakt orwechsel Gelenkwell enlänge beachten @ 6\mod_12 14996938591_78.doc x @ 97742 @ @ 1
Caution! - Changing the tractor
Effect: Damage to the machine
When using the machine for the first time and whenever changing the tractor Check PTO shaft
for the correct length. If the length of the PTO shaft does not match the tractor, always observe
the chapter entitled "Adjusting the length of the PTO shaft".
Pos: 32.12.4 /BA/Er stinbetriebnahme/ Gelenkwelle/Schwader /Längenanpassung Bi ld Schwader 807-1 bis 810- 1 / 905-1+906-1 / 900# @ 146\mo d_1360079146484_78.doc x @ 1307447 @ @ 1
2
SW9070052
1
Fig. 18
Pos: 32.12.5 /BA/Er stinbetriebnahme/ Gelenkwelle/Schwader Längenanpassung_ mit Weitwinkel Text_Sc hwader und Wender neu @ 486\mod_1 480602888961_78.doc x @ 3272016 @ @ 1
The universal shaft length must be adapted.
• Connect the machine to the tractor without universal shaft.
• Drive the three-point hitch in all the way.
• Move the machine in the shortest position for the universal shaft and lower the lower links, if
necessary.
The shortest position is reached when the PTO shaft end of the tractor and the drive journal of
the machine are at the same height (horizontal).
• Park the machine on the support jack.
• Switch off the tractor, remove the ignition key and carry it with you and secure the machine
against rolling away.
• Disassemble the universal shaft.
• Attach the universal shaft half with the wide-angle coupling (1) on machine side.
• Attach the other universal shaft half (2) on tractor side.
Observe the marking on the universal shaft.
For further procedure, refer to the operating instructions of the universal shaft manufacturer.
Pos: 32.12.6 /BA/Er stinbetriebnahme/ Gelenkwelle/Hinwei s Schwenkbereich/Fr eiraum beachten @ 6\mod_12 14544723898_78.doc x @ 94820 @ @ 1
Note
Check the swivel range and clearance of the PTO shaft! Damage can be caused if the tractor or
the machine touch the PTO shaft (e.g. hitching device, hitching frame, lower suspension arms).
Pos: 32.13 /Layout Module /---------------Seitenumbruch---------------- @ 0\mod_1196175311226_0. docx @ 4165 @ @ 1