How to remove moire pattern on Kyocera TASKalfa 180 All in One Printer copies?
If you see a moire pattern on copies from your Kyocera All in One Printer, and the original is a printed photograph, set the image quality mode to 'Photo'.
Why are my Kyocera All in One Printer copies blank?
If your Kyocera All in One Printer copies come out blank, ensure the originals are set correctly. When using the platen, place them face-down along the original size indicator plates. If using the document processor, set them face-up.
How to fix vertical lines on Kyocera All in One Printer copies?
If black or white vertical lines appear on copies from your Kyocera All in One Printer, the electrical charge section might be dirty. Open the front cover and use the charger cleaner rod to clean it.
Why are my Kyocera All in One Printer copies curled?
If your Kyocera All in One Printer copies are curled, it could be due to wet copy paper; replace it with dry, new paper. Also, if 'Middle 2' is set at the Paper type (Paper Weight) setting, change it to 'Middle 1'.
How to clean Kyocera TASKalfa 180 All in One Printer for dirty copies?
If your Kyocera All in One Printer produces dirty copies, the platen or the original cover might be dirty. Clean the platen and/or the original cover to resolve this issue.
Why does my Kyocera TASKalfa 180 paper jam so often?
If your Kyocera All in One Printer often experiences paper jams, ensure the paper is loaded correctly. Also, check if the paper is of the supported type and in good condition; try removing the paper, turning it over, and reloading it. Replace curled, folded, or wrinkled paper with new paper. Finally, remove any loose scraps or jammed paper from the machine.
How to fix skewed copies on Kyocera TASKalfa 180 All in One Printer?
If your Kyocera All in One Printer is producing skewed copies, make sure the originals are set correctly. When using the platen, securely align the original along the original size indicator plates. Also, check the width guide plate position in the cassette to ensure the paper is set correctly.
Why are my Kyocera All in One Printer copies too dark?
If your Kyocera All in One Printer copies are too dark, it might be due to the auto density adjustment mode being enabled. To correct this, perform the auto density adjustment procedure. Alternatively, if the manual density mode is set, use the Lighter key or the Darker key to properly adjust the density level.
Why are my Kyocera All in One Printer copies too light?
If your Kyocera All in One Printer copies are too light, several factors could be the cause: * The auto density adjustment mode might be enabled. To resolve this, perform the auto density adjustment procedure. * If the manual density mode is set, use the Lighter or Darker key to adjust the density. * The toner may not be evenly distributed. Shake the toner container horizontally about 10 times. * EcoPrint mode might be activated; disable it. * The copy paper might be wet; replace it with new paper. * The electrical charge section could be dirty; open the front cover and clean it with the charger cleaner rod.
How to fix moire pattern on Kyocera TASKalfa 180 All in One Printer copies?
If your Kyocera All in One Printer copies have a moire pattern, and the original is a printed photograph, select “Photos” in the Image Quality Mode.
Step-by-step instructions for performing basic copying operations.
How to manually adjust the copy density for desired output.
Adjusts the magnification to reduce or enlarge the original image.
Instructions for making two-sided copies from originals.
Guides users on how to modify the machine's default settings.
Provides an overview of the job accounting features and capabilities.
General| Duplex printing | No |
|---|---|
| Print technology | Laser |
| Maximum resolution | 2400 x 600 DPI |
| Economical printing | Yes |
| Time to first page (black, normal) | 5.7 s |
| Print speed (black, normal quality, A3) | 8 ppm |
| Print speed (black, normal quality, A4/US Letter) | 18 ppm |
| Safety | TÜV/GS, CE |
| Media thickness | 0.11 mm |
| Dimensions (WxDxH) | 568 x 546 x 502 mm |
| All-in-one functions | Copy, Print |
| Compatible operating systems | Windows 98 SE/ME/2000/XP/Vista |
| Maximum duty cycle | - pages per month |
| Copier resize | 25 - 400 % |
| Maximum copy resolution | 600 x 600 DPI |
| Maximum number of copies | 999 copies |
| Grayscale levels | 256 |
| Optical scanning resolution | - DPI |
| Total input capacity | 300 sheets |
| Total output capacity | 250 sheets |
| Maximum input capacity | 1300 sheets |
| Multi-Purpose tray input capacity | 100 sheets |
| Maximum print size | 297 x 420 mm |
| Paper tray media types | Plain paper |
| Non-ISO print media sizes | Folio |
| ISO A-series sizes (A0...A9) | A3, A4, A5, A6 |
| Maximum ISO A-series paper size | A3 |
| Display | - |
| Market positioning | Business |
| Standard interfaces | USB 2.0 |
| USB 2.0 ports quantity | 1 |
| Processor family | ARM9E |
| Processor frequency | 150 MHz |
| Sound pressure level (printing) | 65.3 dB |
| AC input voltage | 220 - 240 V |
| AC input frequency | 50 - 60 Hz |
| Power consumption (standby) | 60 W |
| Power consumption (average operating) | 424 W |
| Sustainability certificates | ENERGY STAR |
To Next Page
