Lantronix PREMIERWAVE XC HSPA+ - To Configure Tunnel Serial Settings

To Next Page

To Previous Page

6: Network Settings

PremierWave® Intelligent Gateway User Guide 57

To Configure Tunnel Serial Settings

Using Web Manager

 To configure the GRE for a specific tunnel, click GRE.

Using the CLI

 To enter GRE command level: enable -> gre

Using XML

 Include in your file: <configgroup name=”gre”>

Main Page

Default Chapter2
- Intellectual Property2
- Warranty2
- Contacts2
- Disclaimer2
- Revision History3
- Table of Contents4
- List of Figures11
- Premierwave® XC HSPA+ Intelligent Gateway User Guide14
1 : Using this Guide15
- Purpose and Audience15
- Summary of Chapters15
- Additional Documentation16
2 : Introduction17
- Key Features17
- Applications18
- Protocol Support18
- Troubleshooting Capabilities19
- Configuration Methods19
- Addresses and Port Numbers19
- Product Information Label20
- Figure 2-1 Premierwave Unit Product Label20
3 : Installation of the Premierwave XC HSPA+ Device21
- Package Contents21
- User-Supplied Items21
- Hardware Components22
- Installing the Premierwave XC HSPA+ Unit Device26
- Figure 3-11 Premierwave XC HSPA+ Bottom/Back Panel View26
- Table 3-12 Premierwave XC HSPA+ Connections (Side)26
- Figure 3-13 SIM Card Insertion27
- Figure 3-14 Premierwave XC HSPA+ Unit Dimensions in Inches (In)28
4 : Device Discovery and Quick Setup29
- Accessing the Premierwave XC HSPA+ Device Using Upnp29
- Accessing the Premierwave XC HSPA+ Device Using Deviceinstaller30
- Device Detail Summary30
5 : Configuration Using Web Manager32
- Accessing Web Manager32
- Device Status Page33
- Figure 5-1 Device Status Page33
- Web Manager Components34
- Figure 5-2 Components of the Web Manager Page34
- Navigating Web Manager35
6 : Network Settings38
- Network 1 Status38
- Network 1 (Eth0) Interface Settings38
  - Table 6-1 Network Interface Settings38
  - To Configure Network 1 Interface Settings40
- Network 1 (Eth0) Link Settings41
  - To Configure Network 1 Link Settings41
- Network 1 (Eth0) Qos41
- Network 1 (Eth0) Failover43
  - To Configure Network 1 Failover Settings43
  - Table 6-5 Network 1 (Eth0) Failover Settings43
- Network 2 Status44
- Network 2 (Cellular "Wwan0") Interface Settings44
- Gateway47
- Ddns53
- Vpn54
  - Table 6-23 VPN Configuration54
  - To Configure VPN Settings56
- GRE Settings56
  - Table 6-24 GRE Settings56
  - To Configure Tunnel Serial Settings57
7 : Cellular58
- To Configure Cellular Settings58
- Typical Cellular Error (Errcodes)59
8 : Input/Output Ports60
- Relay Output60
  - To Configure Relay Settings60
  - Table 8-1 Relay Output Settings60
- Digital Input61
  - To Configure Digital Input Settings61
  - Table 8-2 Digital Input Settings61
9 : Action Settings62
- Alarms and Reports62
- Actions62
  - Table 9-1 Action Settings62
  - To Configure Action Settings63
- Python64
  - Ide64
- Applications65
  - Table 9-2 Script Settings65
  - To Configure Application Settings66
10 : Line and Tunnel Settings67
- Line Statistics67
- Line Settings67
- Tunnel Statistics70
  - To View Tunnel Statistics70
- Tunnel Settings70
11 : Terminal and Host Settings81
- Terminal Settings81
- Host Configuration82
  - Table 11-2 Host Configuration82
  - To Configure Host Settings83
12 : Network Services84
- DNS Settings84
  - To View or Configure DNS Settings84
  - Table 12-1 DNS Settings84
- FTP Settings85
  - To Configure FTP Settings85
- Syslog Settings85
- HTTP Settings86
  - To Configure HTTP Settings87
  - To Configure HTTP Authentication88
- RSS Settings88
- SNMP Settings89
  - To Configure SNMP Settings89
  - Table 12-7 SNMP Settings89
- Discovery90
  - To Configure Discovery90
  - Table 12-8 Discovery Settings90
- SMTP Settings91
  - To Configure SMTP Settings91
- Email Settings91
13 : SMS Settings93
- Inbound SMS93
- Outbound SMS93
- Table 13-1 Inbound SMS Settings93
- Table 13-2 Adding a New SMS Settings93
- Table 13-3 Outbound SMS Settings93
- To Configure Inbound SMS94
- To Configure Outbound SMS94
14 : Updating Firmware95
- Obtaining Firmware95
- Loading New Firmware through Web Manager95
- Figure 14-1 Uploading New Firmware96
- Loading New Firmware through FTP97
15 : Security Settings98
- Public Key Infrastructure98
- Tls (Ssl)98
- Digital Certificates99
- Trusted Authorities99
- Obtaining Certificates99
- Self-Signed Certificates99
- Certificate Formats99
- Openssl100
- SSH Settings100
- SSL Settings104
16 : Maintenance and Diagnostics Settings108
- Filesystem Settings108
- Protocol Stack Settings110
- Diagnostics113
- Clock117
  - To Specify Clock Setting Method117
  - Table 16-11 Clock Settings117
- System Settings118
  - To Reboot or Restore Factory Defaults118
  - Table 16-12 System Settings118
17 : Management Interface Settings119
- Command Line Interface Settings119
- XML Settings121
18 : Branding the Premierwave XC HSPA+ Device125
- Web Manager Customization125
- Short and Long Name Customization126
  - To Customize Short or Long Names126
  - Table 18-1 Short and Long Name Settings126
Appendix A: Technical Specifications127
- Network127
  - Cellular127
  - Ethernet127
- Serial Interface127
- Serial Connector127
- USB Interface127
- USB Connector128
- I/O Interface128
  - Input128
  - Output128
- I/O Connectors128
- LED Indicators128
- Routing/Gateway128
- Protocol Support129
- Event Triggers and Actions129
- Security129
- Management129
- Software129
- Power130
- Environmental130
- Dimensions130
Appendix B: Compliance131
Appendix C: Lantronix Technical Support134
Appendix D: Binary to Hexadecimal Conversions135
- Converting Binary to Hexadecimal135
  - Conversion Table135
  - Scientific Calculator135
- Table D-1 Binary to Hexadecimal Conversion135
- Figure D-2 Windows Scientific Calculator136
- Figure D-3 Hexadecimal Values in the Scientific Calculator136

Lantronix PREMIERWAVE XC HSPA+ - To Configure Tunnel Serial Settings

Table of Contents

Other manuals for Lantronix PREMIERWAVE XC HSPA+

Related product manuals