LELY DISCOVERY 90 S - User Manual

Questions and Answers

S
Scott SmithSep 7, 2025
What to do if LELY DISCOVERY 90 S Discovery says battery power too low to start route?
- R
  rayshannonSep 7, 2025
  If the LELY Vacuum Cleaner Discovery's battery power is too low to start a route, it may be due to bad contact with the battery charger caused by dirt or corrosion, loose connections, or the battery level being too low before starting. To fix this, clean the charging strips and electrodes, manually drive the Discovery to the charging station, and ensure the battery is charging. If it still doesn't charge, contact your local service provider.
A
annahernandezAug 22, 2025
How to fix LELY Ultrasonic Jewelry Cleaner 'EMPTY_BATTERY' error?
- Z
  Zachary HallAug 22, 2025
  To resolve the 'EMPTY_BATTERY' error on your LELY Ultrasonic Jewelry Cleaner, indicating low battery power, follow these steps: * Clean the charging strips and electrodes to ensure good contact. * Manually move the machine to the charging station. * Verify that the battery is charging correctly. If the issue persists, it may be necessary to contact your local service provider.
H
Heather MyersSep 5, 2025
How to solve 'NO TIME' error on LELY Ultrasonic Jewelry Cleaner?
- M
  Michael Torres MDSep 5, 2025
  To solve the 'NO TIME' error on your LELY Ultrasonic Jewelry Cleaner, set the time path and try again.
J
Julia ThompsonSep 3, 2025
How to fix 'ROUTE-MEMORY' full error on LELY Ultrasonic Jewelry Cleaner?
- B
  Barry ProctorSep 3, 2025
  To address the 'ROUTE-MEMORY' error on your LELY Ultrasonic Jewelry Cleaner, delete a route before programming a new one.
S
Stephanie VanceSep 2, 2025
How to resolve 'SKIDDING_STOP' error on LELY Ultrasonic Jewelry Cleaner?
- T
  Todd WagnerSep 2, 2025
  If your LELY Ultrasonic Jewelry Cleaner shows 'SKIDDING_STOP', take these steps: * Make sure the manure scraper is not worn out; replace it if necessary. * Manually run the route again. * If the problem persists, decrease the motor power.
P
patricia85Aug 31, 2025
What to do for 'DIS_OFF_RANGE' error on LELY Ultrasonic Jewelry Cleaner?
- J
  Joseph MendezAug 31, 2025
  To resolve the 'DIS_OFF_RANGE' error on your LELY Ultrasonic Jewelry Cleaner, try the following: * Calibrate the gyroscope. * Test the route. If the problem remains: * Do a route analysis. * Modify the routes that are unreliable. * Test the route. If the problem still persists, contact your local Lely service provider.
S
stephanie83Aug 30, 2025
How to troubleshoot 'NO_ULTRASIGN' error on LELY Ultrasonic Jewelry Cleaner?
- T
  Tracy ParkerAug 30, 2025
  To address the 'NO_ULTRASIGN' error on your LELY Ultrasonic Jewelry Cleaner: * Clean the Ultrasonic Sensor. * Clean the Sensing Wheel. * Test the Ultrasonic Sensor.
C
Charles DaviesAug 29, 2025
How to fix 'CLOCK ERROR' on LELY Ultrasonic Jewelry Cleaner?
- K
  Kimberly ReevesAug 29, 2025
  To fix the 'CLOCK ERROR' on your LELY Ultrasonic Jewelry Cleaner, follow these steps: * Ensure the real-time clock is set in the correct 24-hour format. * Verify that all start and end times in the time path are entered in the correct 24-hour format. * Correct the clock or the start and end times if necessary.
P
Patricia PalmerAug 27, 2025
What to do if LELY Ultrasonic Jewelry Cleaner shows 'BLOCKAGE_DISC'?
- A
  awillisAug 28, 2025
  If your LELY Ultrasonic Jewelry Cleaner displays 'BLOCKAGE_DISC', follow these steps: * Ensure there are no obstacles. * Try running the route again. If the machine is blocked on the same place: * Do a route analysis. * Modify the routes that are unreliable. If the machine is blocked at a different place, calibrate the gyroscope.
P
Patrick WheelerAug 27, 2025
How to resolve LELY Ultrasonic Jewelry Cleaner 'TURN BLOCK' error?
- K
  Kimberly VargasAug 27, 2025
  To address a 'TURN BLOCK' error on your LELY Ultrasonic Jewelry Cleaner, follow these steps: * Ensure there are no obstructions. * Inspect the sliding disc and replace it if it's worn. * Check the manure scraper and replace it if necessary.