LELY Discovery 90 SW - User Manual

Questions and Answers

G
gina83Aug 18, 2025
How to fix no charging current on LELY Discovery 90 SW Ultrasonic Jewelry Cleaner?
- M
  Monica GoodmanAug 18, 2025
  If your LELY Ultrasonic Jewelry Cleaner isn't charging, start by ensuring there are no obstacles blocking it from reaching the charging station. Then, clean both the charging strips and the charging electrodes. If it still doesn't charge, manually drive it to the charging station and check that the battery is indeed charging. If the issue persists, it might be due to bad contact with the battery charger caused by dirt and/or corrosion, or loose connections.
G
Gary MooreAug 20, 2025
What to do if LELY Discovery 90 SW battery power is too low?
- B
  Brooke GonzalezAug 20, 2025
  If your LELY Ultrasonic Jewelry Cleaner's battery power is too low to start, it could be due to bad contact with the battery charger from dirt or corrosion, or loose connections. First, clean the charging strips and electrodes. Next, manually drive the machine to the charging station. Then, ensure the battery is charging. If it's still not charging, it is advised to contact your local service provider.
J
james85Aug 22, 2025
What to do if LELY Ultrasonic Jewelry Cleaner is blocked?
- J
  Jill DixonAug 23, 2025
  If your LELY Ultrasonic Jewelry Cleaner is blocked, first make sure there are no obstacles. Try running the route again. If it gets blocked in the same place, perform a route analysis and modify any unreliable routes. However, if it's blocked in a different place, calibrate the gyroscope. The cause may be an obstacle or an inaccurate gyroscope.
F
Frederick LoveAug 25, 2025
Why LELY Discovery 90 SW Ultrasonic Jewelry Cleaner battery recharge failed?
- R
  Robert BoyerAug 26, 2025
  If your LELY Ultrasonic Jewelry Cleaner's battery recharge failed with too low charging current, it could be due to bad contact with the battery charger because of dirt, corrosion, or loose connections. To resolve this, clean the charging strips and the charging electrodes, and then make sure the battery is charging.
J
Jennifer HernandezAug 28, 2025
Why LELY Ultrasonic Jewelry Cleaner can not take the turn?
- C
  colleenhuntAug 28, 2025
  If your LELY Ultrasonic Jewelry Cleaner is not able to take the turn, first ensure that there are no obstacles. Then, check if the sliding disc is worn out and replace it if needed. Also, make sure the manure scraper isn't worn out, and replace it if necessary. This issue can arise from a mechanical problem, worn parts, or dirt causing resistance, or if the vehicle hasn't turned far enough.
E
Elizabeth BrownAug 30, 2025
How to fix LELY Discovery 90 SW turns more than 360 degrees?
- U
  ugarrisonAug 30, 2025
  If your LELY Ultrasonic Jewelry Cleaner turns more than 360 degrees, calibrate the gyroscope, as this issue is caused by the turn exceeding 360 degrees.
J
Jamie HullSep 1, 2025
What to do if LELY Discovery 90 SW not charged for 24 hours?
- E
  emilystanleySep 2, 2025
  If your LELY Ultrasonic Jewelry Cleaner has been not charged or started a route for more than 24 hours, clean the charging strips and electrodes, ensure the battery is charging, and charge the machine. The machine stops and beeps for 1 hour.
L
Larry FrazierSep 4, 2025
How to fix no ultrasound signal on LELY Ultrasonic Jewelry Cleaner?
- G
  Gary JohnsonSep 4, 2025
  If your LELY Ultrasonic Jewelry Cleaner has no ultrasound signal, clean the ultrasonic sensor and the sensing wheel, and test the ultrasonic sensor. This issue can be caused by dirt on the ultrasonic sensor or sensing wheel, the absence of an object within the sensor's reach, or a broken sensor.
L
Lisa MorenoSep 7, 2025
How to fix LELY Discovery 90 SW route memory full?
- K
  Kelly PerezSep 7, 2025
  If your LELY Ultrasonic Jewelry Cleaner's route memory is full, delete a route before programming a new one. This is because the route memory has reached its maximum of 16 different routes.
H
heatherriveraSep 9, 2025
What to do if LELY Ultrasonic Jewelry Cleaner battery runs down?
- A
  ana49Sep 9, 2025
  If your LELY Ultrasonic Jewelry Cleaner's battery runs down, clean the charging strips and the charging electrodes, make sure the battery is charging and charge the machine.