Lenovo ThinkServer TD350 - Configuring the TPM Function; Setting an Ethernet Connector for System Management; Exiting the Setup Utility Program

3.PressF10tosavesettingsandexittheSetupUtilityprogram.Theserverwillfollowthestartupdevice
sequenceyouhaveseteachtimeyouturnontheserver.
ConfiguringtheTPMfunction
TheTPMworksasahardwaresecuritysolutiontohelpyoutoencryptdataandprotecttheserver.TheTPM
functionisonlyavailablewhenthereisaTPMinstalledinyourserver.See“InstallingtheTPM”onpage111.
YoucanpurchaseaTPMfromtheLenovoWebsiteat:
http://lenovoquickpick.com/usa/home/thinkserver/rack-and-tower-server
AfterinstallingaTPM,checkiftheTPMfunctionisenabledintheSetupUtilityprogram.
ToenabletheTPMfunctionintheSetupUtilityprogram,dothefollowing:
1.StarttheSetupUtilityprogram.See“StartingtheSetupUtilityprogram”onpage57.
2.OntheSystemSecuritymenu,selectTPMSettings➙TPMSupport.
3.Dooneofthefollowing:
•IfTPMSupportissettoEnabled,theTPMSecurityFeatureitemisdisplayed.SetTPMSecurity
FeaturetoActivate.
•IfTPMSupportissettoDisabled,dothefollowing:
a.SetTPMSupporttoEnabledandpressF10tosavesettingsandexittheSetupUtilityprogram.
Theserverwillrestart.
b.StarttheSetupUtilityprogram.OntheSystemSecuritymenu,selectTPMSettings.Then,set
TPMSecurityFeaturetoActivate.
4.PressF10tosavesettingsandexittheSetupUtilityprogram.Theserverwillrestarttoenablethe
TPMfunction.
SettinganEthernetconnectorforsystemmanagement
TherearethreeRJ-45Ethernetconnectorsontherearoftheserver.Ethernetconnector0isforsystem
managementbydefault.However,youalsocansetEthernetconnector1forsystemmanagementuse.
Whenusedforsystemmanagement,Ethernetconnector1andEthernetconnector0cannotbeteamed
orsetforfailover.Onlyoneofthemcanbeusedatatime.TolocatethethreeEthernetconnectors,see
“Rearviewoftheserver”onpage22
.
TosettheEthernetconnectorforsystemmanagement,dothefollowing:
1.StarttheSetupUtilityprogram.See“StartingtheSetupUtilityprogram”onpage57.
2.OntheTSMSettingsmenu,selectTSMNetworkSettings➙TSMNICSelection.
3.Dooneofthefollowing:
•TosettheEthernetconnector0forsystemmanagement,selectDedicatedPort.
•TosettheEthernetconnector1forsystemmanagement,selectSharedNICPort.
4.PressF10tosavesettingsandexittheSetupUtilityprogram.
ExitingtheSetupUtilityprogram
Afteryoufinishviewingorchangingsettings,pressEsctoreturntotheSetupUtilityprogrammaininterface.
Ifyouareonanestedsubmenu,pressEscrepeatedlyuntilyoureachthemaininterface.Then,youcando
oneofthefollowingtoexittheSetupUtilityprogram:
•IfyouwanttosavethenewsettingsandexittheSetupUtilityprogram,pressF10orselectSave&Exit➙
SaveChangesandReset.Otherwise,yourchangeswillnotbesaved.
62ThinkServerTD350UserGuideandHardwareMaintenanceManual