●
DIGITAL KEY TELEPHONE / Quick Reference Guide KD, KD/E, LKD Series
Fixed Feature Buttons
● FLASH button is used to terminate an outside call
and re-seize dial tone without having to hang up
the handset.
● SPEED button provides you with access to speed
dialing, save number redial and last number redial.
● TRANS (TRANSFER) button is used to transfer an
outside call from a station to another.
Quick Reference Guide for Digital Key Telephone
● MUTE button allows you to switch the built in
microphone on or off when using the speakerphone
or the handset microphone when using the handset.
● MON/SPEAKER button enables you to make a phone
call without lifting handset. It turns the telephone on
and off when using the speakerphone.
● HOLD button enables you to place an outside caller
Quick Ref. Gui
● CALLBK (CALLBACK) button allows you to leave
a callback indication at a station that is busy,
unattended, or in Do Not Disturb.
● CONF button is used to establish conference calls.
● DND/FWD (Do Not Disturb/FORWARD) button
allows you to forward your calls to another
destination, or make DND mode.
on hold.
● REDIAL allows you to make last number redial and
auto call number redial.
● ▼ VOLUME ▲ bar allows you to adjust speakerphone
and handset volume.
Call Forward
Leaving a Message Waiting Indication
If you dial a station that is unattended or in Do
de
.
● Press DND/FWD button and dial the desired Call
Forward type.
- 0 : Follow me (not available in GDK-16/20W)
- 1 : Unconditional
- 2 : Busy calls
- 3 : No answer calls
- 4 : Busy/no answer calls
- 5 : Station off-net
- 6 : Incoming outside line to off-net (Sys. ATD only)
- 7 : No Answer DVU forward-1(after 4sec)
- 8 : No Answer DVU forward-2(after predefined time)
- 9 : Bus
DVU forward
Not Disturb, you can leave a message waiting
indication.
● Dial the desired intercom station. Busy tone or
DND tone is heard.
● Press CALLBK button. The called party’s CALLBK
button LED will flash.
To answer a Message Waiting Indication,
● Press flashing CALLBK button and the station that
left message will be signaled with tone ringing.
● If called station does not answer, press the CALLBK
button once to leave a messa
e.
- # : Cancel previous call forward
● Dial the station number or press DSS button or
intercom group where calls are forwarded.
(Confirmation tone is heard.)
Call Wait (Camp-on)
If you dial a busy station, you may alert it to your call.
● After receiving intercom busy tone, dial * or the last
digit of called station number or press DSS button.
● When the called party answers, consult with them
or hang up to transfer the call, if any.
Placing an Outside Call on Hold
While connected to an outside line,
● Press HOLD/SAVE button.
- Once for system hold
- Twice for exclusive hold
● Reverse if hold preference is programmed to
system hold.
● Press HOLD/SAVE button. (in GDK-16/20W)
CO line call will be put on hold according to the
Hold Preference.
Conference
● Call the desired party (internal or outside). When
called party answers, press CONF button.
● Add next conference party by selecting another
outside line or intercom station.
● When the party answers, press CONF button twice.
All parties are connected.
To terminate a conference,
The conference initiator should be actively in the
conference.
● Hang up, or press CONF button to finish the
Last Number Redial
The last dialed number on an outside line is saved.
● Press REDIAL button. Or,
● Press SPEED button and dial *.
Save Number Redial (＊)
If you wish to save a number you dialed,
● After dialing the number of an outside party, keep
the handset off-hook.
● Press SPEED button twice.
To dial a saved number,
● Press SPEED button and dial #.
conference (only for conference initiator).
Note : The feature which is marked
(＊), is not available in GDK-16/20W.
To Next Page
Need help?
General
