Mitsubishi Electric MELSEC-A/QnA Series - Page 267

7 POSITIONING MODULE REPLACEMENT
7 - 30
Speed designation during OP shift
88 238
388 88 238 388
Dwell time during OPR retry
89 239
389 89 239 389
Absolute position restoration
selection
91 241
391 - - -
Servo series
100 250
400 30100 30200 30300
Amplifier setting
101 251
401 30101 30201 30301
Regenerative brake resistor
102 252
402 30102 30202 30302
Motor type
103 253
403 30103 30203 30303
Motor capacity
104 254
404 30104 30204 30304
Servo motor speed
105 255
405 30105 30205 30305
Feed back pulse
106 256
406 30106 30206 30306
Rotation direction selection
107 257
407 30107 30207 30307
Auto tuning
108 258
408 30108 30208 30308
Servo response
109 259
409 30109 30209 30309
Maker setting - - - 30110 30210 30310
Maker setting - - - 30111 30211 30311
Load inertia ratio
112 262
412 30112 30212 30312
Position loop gain 1
113 263
413 30113 30213 30313
Speed loop gain 1
114 264
414 30114 30214 30314
Position loop gain 2
115 265
415 30115 30215 30315
Speed loop gain 2
116 266
416 30116 30216 30316
Speed integral compensation
117 267
417 30117 30217 30317
Notch filter selection
118 268
418 30118 30218 30318
Feed forward gain
119 269
419 30119 30219 30319
In-position range
120 270
420 30120 30220 30320
Electromagnetic brake sequence
output
121 271
421 30121 30221 30321
Analog monitor output
122 272
422 30122 30222 30322
Optional function 1
123 273
423 30123 30223 30323
Optional function 2
124 274
424 30124 30224 30324
Adaptive vibration suppression
control/ low pass filter
125 275
425 30125 30225 30325
Maker setting
--
- 30126 30226 30326
Monitor output 1 offset
127 277
427 30127 30227 30327
Monitor output 2 offset
128 278
428 30128 30228 30328
Pre-alarm data selection
129 279
429 30129 30229 30329
Zero speed
130 280
430 30130 30230 30330
Error excessive alarm level
131 281
431 30131 30231 30331
Optional function 5
132 282
432 30132 30232 30332
Optional function 6
133 283
433 30133 30233 30333
PI-PID control switch-over position
droop
134 284
434 30134 30234 30334
Item of AD75M
Buffer memory address
AD75M QD75M
Axis 1 Axis 2 Axis 3 Axis 1 Axis 2 Axis 3
Pr.57
Pr.58
Pr.59
Pr.100
Pr.101
Pr.102
Pr.103
Pr.104
Pr.105
Pr.106
Pr.107
Pr.108
Pr.109
Pr.112
Pr.113
Pr.114
Pr.115
Pr.116
Pr.117
Pr.118
Pr.119
Pr.120
Pr.121
Pr.122
Pr.123
Pr.124
Pr.125
Pr.126
Pr.127
Pr.128
Pr.129
Pr.130
Pr.131
Pr.132
Pr.133
Pr.134