APP - 44
APPENDICES
Table 1.14 Parameter warning (2301 to 2599)/Parameter error (2601 to 2899) error detail (Continued)
Error code
Parameter
No.
Name Error code
Parameter
No.
Name
2377 2677 PC13
Analog monitor feedback position output
standard data Low
2416 2716 PD20
Driver communication setting
Master axis No. selection1 for slave
2378 2678 PC14
Analog monitor feedback position output
standard data High
2417 2717 PD21
For manufacturer setting
2379 2679 PC15 For manufacturer setting 2418 2718 PD22
2380 2680 PC16 Function selection C-3A 2419 2719 PD23
2381 2681 PC17 Function selection C-4 2420 2720 PD24
2382 2682 PC18
For manufacturer setting
2421 2721 PD25
2383 2683 PC19 2422 2722 PD26
2384 2684 PC20 Function selection C-7 2423 2723 PD27
2385 2685 PC21 Alarm history clear 2424 2724 PD28
2386 2686 PC22
For manufacturer setting
2425 2725 PD29
2387 2687 PC23 2426 2726 PD30
Master-slave operation - Torque command
coefficient on slave
2388 2688 PC24 2427 2727 PD31
Master-slave operation - Speed limit
coefficient on slave
2389 2689 PC25 2428 2728 PD32
Master-slave operation - Speed limit
adjustment value on slave
2390 2690 PC26 2429 2729 PE01
For manufacturer setting
2391 2691 PC27 2430 2730 PE02
2392 2692 PC28 2431 2731 PE03
2393 2693 PC29 2432 2732 PE04
2394 2694 PC30 2433 2733 PE05
2395 2695 PC31 2434 2734 PE06
2396 2696 PC32 2435 2735 PE07
2397 2697 PD01 2436 2736 PE08
2398 2698 PD02 2437 2737 PE09
2399 2699 PD03 2438 2738 PE10
2400 2700 PD04 2439 2739 PE11
2401 2701 PD05 2440 2740 PE12
2402 2702 PD06 2441 2741 PE13
2403 2703 PD07 Output signal device selection 1 (CN3-13) 2442 2742 PE14
2404 2704 PD08 Output signal device selection 2 (CN3-9) 2443 2743 PE15
2405 2705 PD09 Output signal device selection 3 (CN3-15) 2444 2744 PE16
2406 2706 PD10 For manufacturer setting 2445 2745 PE17
2407 2707 PD11 Input filter setting 2446 2746 PE18
2408 2708 PD12
For manufacturer setting
2447 2747 PE19
2409 2709 PD13 2448 2748 PE20
2410 2710 PD14 Function selection D-3 2449 2749 PE21
2411 2711 PD15 Driver communication setting 2450 2750 PE22
2412 2712 PD16
Driver communication setting
Master transmit data selection1
2451 2751 PE23
2413 2713 PD17
Driver communication setting
Master transmit data selection2
2452 2752 PE24
2414 2714 PD18
For manufacturer setting
2453 2753 PE25
2415 2715 PD19 2454 2754 PE26 Filter coefficient 2-1
(Note): The details are different when using the servo amplifiers with a large capacity.
Refer to the "Servo amplifier Instruction Manual" for details.
To Next Page
Loading...
