OEM PF 33 MT - English

PF 33 MT - PF 46 MT
General specifications and warning
EN - 1
ENGLISH
CHAPTER ........................................................ 1
Chapter for the technician and operator
1.1 GENERAL WARNINGS ..................................... Pag. EN-2
1.2
REFERENCE NORMATIVE .............................. Pag. EN-3
1.3
DESCRIPTION OF THE SYMBOLS ................ Pag. EN-3
1.4 COMPOSITION OF THE MACHINE ................ Pag. EN-4
1.5 PREARRANGEMENTS AT PURCHASERʼS
CHARGE ............................................................ Pag. EN-4
1.6
EMERGENCY OPERATIONS IN CASE
OF FIRE
............................................................. Pag. EN-4
1.7 EXPLOSION RISK ............................................. Pag. EN-4
1.8 SOUND PRESSURE LEVEL ............................ Pag. EN-4
CHAPTER ........................................................ 2
Chapter for the technician
- OVERALL DIMENSIONS ....................................... Pag. EN-5
2.1 TECHNICAL FEATURES ................................. Pag. EN-5
2.2 TRANSPORT ..................................................... Pag. EN-6
2.2.a Shipment ................................................... Pag. EN-6
2.2.b Lifting of the packing ................................ Pag. EN-6
2.2.c Storage ...................................................... Pag. EN-6
2.3 RECEPTION OF THE MACHINE ..................... Pag. EN-7
2.4 UNPACKING ...................................................... Pag. EN-7
2.5 IDENTIFICATION OF THE COMPONENTS ... Pag. EN-8
2.6 IDENTIFICATION OF THE MACHINE ............. Pag. EN-8
CHAPTER ........................................................ 3
Chapter for the technician
3.1 LIFTING OF THE MACHINE ............................ Pag. EN-9
3.2 POSITIONING OF THE MACHINE .................. Pag. EN-9
3.2.a Bench machine positioning ...................... Pag. EN-9
3.2.b Positioning on trailer-mounted support Pag. EN-10
3.3 ELECTRICAL CONNECTION ........................ Pag. EN-10
3.3.a Control of a correct electrical
connection ................................................Pag. EN-11
3.3.b Unipotential connection ...........................Pag. EN-11
3.4 FIRST START ...................................................Pag. EN-11
CHAPTER ........................................................ 4
Chapter for the technician and operator
4.1 TYPE OF USE AND CONTRAINDICATIONS ....... Pag. EN-12
4.2 SAFETY PLATES ........................................... Pag. EN-12
4.3
SAFETY DEVICE ............................................. Pag. EN-15
4.4
OPERATOR AREAS ........................................ Pag. EN-16
4.5 RESIDUAL RISK ZONES .................................. Pag. EN-16
CHAPTER ........................................................ 5
Chapter for the technician and operator
5.1 CONTROL BOARD AND PILOT LAMPS ....... Pag. EN-17
5.2
MACHINE PREPARATION ............................ Pag. EN-18
5.3
MACHINE FUNCTIONING .............................. Pag. EN-18
5.3.a Temperature adjustment ......................... Pag. EN-19
5.3.b Machine stopping under
emergency conditions ........................... Pag. EN-19
5.3.c
Machine disconnection ........................... Pag. EN-19
5.4
TROUBLES, CAUSES ANDCURE ................ Pag. EN-20
CHAPTER ........................................................ 6
Chapter for the technician and operator
6.1 ROUTINE AND PLANNED MAINTENANCE ..... Pag. EN-21
6.1.a In general ................................................ Pag. EN-21
6.1.b Routine maintenance ............................ Pag. EN-21
6.1.b - a Cleaning machine ............................. Pag. EN-21
6.1.c Planned maintenance works ................. Pag. EN-22
6.1.c - a Rack greasing .................................... Pag. EN-22
6.1.d Maintenance operations
as needed .............................................
Pag. EN-22
6.1.d - a Checking parallelism between
the two dishes .................................... Pag. EN-22
6.1.d - b Resetting the safety thermostat .... Pag. EN-23
6.1.d - c Eliminating play from wear .............. Pag. EN-23
CHAPTER ........................................................ 7
Chapter for the technician
7.1 DISMANTLING THE MACHINE .................... Pag. EN-24
7.2 DEMOLISHING THE MACHINE ..................... Pag. EN-24
7.3 DISPOSING OF HARMFUL SUBSTANCES . Pag. EN-24
WIRING DIAGRAM ................................................ Pag. EN-25
SINGLE-PHASE WIRING DIAGRAM ...................... Pag. EN-26