What to do when Oki ML1120 Printer prints content of a single sheet on two sheets when using cut sheets?
If your Oki printer is printing the content of a single cut sheet across two sheets, match the paper setting selected in the application with the physical paper in use. Also, leave enough top and bottom margin in the application. Finally, correct the cut sheet LF adjustment.
Why the platen rotates without paper feed, or continuous forms instead of cut sheets are fed on Oki Printer?
If the platen rotates without feeding paper, or if continuous forms are fed instead of cut sheets on your Oki printer, ensure that the sheets are loaded to the end. If that's not the issue, the printer may be in continuous forms mode; eject the continuous forms and select cut sheet mode for the printer.
What to do if Oki Printer characters are too pale?
If the characters printed by your Oki printer are too pale, first ensure that the Paper Thickness lever position matches the paper type. If it is set correctly, check if the printer is set to print at high speed and set the speed to normal. If the issue persists, the ribbon may be at the end of its life or not installed correctly; try replacing or reinstalling the ribbon cartridge. The ribbon may also be wound incorrectly or not transferring properly, in which case, replace the ribbon cartridge.
What to do if there is no line feed and no paper feed on Oki Printer?
If there is no line feed and no paper feed on your Oki printer, make sure the paper is correctly reloaded on the Pin Tractors. Also, ensure the adjust lever position matches the paper type.
What to do if Oki ML1120 is unable to eject?
If your Oki printer is unable to eject, and the LF/FF button is pressed, press the LOAD/EJECT button.
What to do if the printer driver is not installed properly for Oki ML1120?
If the printer driver is not installed properly for your Oki Printer, reinstall the printer driver correctly.
What to do if there is no paper in the Oki ML1120?
If there is no paper in the Oki Printer, load paper into the printer.
How to fix the Oki ML1120 Printer when paper has run out?
If the Oki Printer is out of paper, add more paper and then press the SEL button.
What to do if continuous forms are jammed in Oki ML1120?
To clear jammed continuous forms in your Oki printer: Turn the power off. Tear off any unprinted forms. Remove the Input Tray and Rear Cover together. Raise each Pin Tractor cover and remove the forms from the Pin Tractors. Rotate the Platen Knob and remove the forms from the front of the printer. Place two or three forms in a stack on the Pin Tractors and turn the Platen Knob to push any remaining fragments out of the printer. Replace the Input Tray and Rear Cover. Turn the power on.
How to resolve cut sheet paper jam in Oki ML1120 Printer?
To resolve a cut sheet paper jam in your Oki printer: Turn the power off. Remove the access cover. Set the Paper Thickness lever to the Replace Ribbon position. Remove the ribbon cartridge. Move the Print Head away from the paper. Rotate the Platen Knob and pull the cut sheet out. Use tweezers if needed. Insert a folded sheet from the Paper Tray and turn the Platen Knob to push out any remaining fragments. Replace the ribbon cartridge and the Access Cover. Turn the power on.
General| Noise level | 49.7 dB |
|---|---|
| Maximum duty cycle | 18000 pages per month |
| Maximum number of copies | 9 copies |
| Power requirements | 120 - 220V |
| Dimensions (WxDxH) | 889 x 587 x 379 mm |
Weight and Dimensions| Dimensions (W x D x H) (imperial) | 35 x 23.1 x 14.9 \ |
|---|
Provides additional information to supplement the main text.
Provides additional information which, if ignored, may result in equipment malfunction or damage.
Provides additional information which, if ignored, may result in a risk of personal injury.
Explains the purpose and structure of the user's guide and related documents.
Instructions on how to read the guide on screen using Adobe Acrobat Reader.
Procedure for printing the whole manual, individual pages, or sections.
Advise to retain packing materials for future shipping or transport.
Identifies and explains the main parts of the printer, including front and rear views.
Details the buttons and indicators on the printer's control panel for operation.
Guidance on selecting a location and powering on the printer for the first time.
Procedure to print a test page to verify printer functionality.
Describes the available data interfaces for connecting the printer to a PC.
Steps for connecting the printer and computer, installing drivers, and printing a test page.
Step-by-step guide on how to load cut sheet paper into the printer.
Instructions on how to manually eject a cut sheet left in the printer.
Procedures for setting up and feeding continuous forms via rear and bottom feeds.
Instructions for tearing off and removing continuous forms from the printer.
Overview of control panels, buttons, and indicators for both ML1120 and ML1190 models.
Describes the specific functions of each button on the printer's control panel.
Instructions on how to change printer modes directly from the front panel.
Guides on setting, confirming, initializing, and viewing printer menu items and values.
Procedures for setting the Top of Form (TOF) position for optimal paper alignment.
Adjusting print speed modes (normal, high, quiet) and setting user-defined TOF positions.
Guides for clearing paper jams for both cut sheet and continuous forms.
Addresses alarm conditions, general problems, printing errors, and paper feed issues.
Instructions for cleaning the outside surfaces of the printer.
Guidance on cleaning the internal components of the printer safely.
Step-by-step instructions for replacing the printer's ribbon cartridge.
Lists consumables and their corresponding order numbers for purchasing.
Covers print method, speed, head, direction, LF/FF time, paper feed control, duplication.
Details character sets, media, ink, print head life, dimensions, weight, power rating, and consumption.
Specifies interfaces, dust/corrosion, operating/storage conditions, standard usage, and noise level.
Covers print method, speed, head, direction, LF/FF time, paper feed control, duplication for ML1190.
Details character sets, media, ink, print head life, dimensions, weight, power rating, and consumption for ML1190.
Specifies interfaces, conditions, usage, and noise level for ML1190.
Provides contact details for Oki Systems offices across various European countries.
To Next Page
