Why the platen rotates without paper feed, or continuous forms instead of cut sheets are fed on Oki Printer?
If the platen rotates without feeding paper, or if continuous forms are fed instead of cut sheets on your Oki printer, ensure that the sheets are loaded to the end. If that's not the issue, the printer may be in continuous forms mode; eject the continuous forms and select cut sheet mode for the printer.
How to resolve cut sheet paper jam in Oki ML1120 Printer?
To resolve a cut sheet paper jam in your Oki printer: Turn the power off. Remove the access cover. Set the Paper Thickness lever to the Replace Ribbon position. Remove the ribbon cartridge. Move the Print Head away from the paper. Rotate the Platen Knob and pull the cut sheet out. Use tweezers if needed. Insert a folded sheet from the Paper Tray and turn the Platen Knob to push out any remaining fragments. Replace the ribbon cartridge and the Access Cover. Turn the power on.
What to do if continuous forms are jammed in Oki ML1120?
To clear jammed continuous forms in your Oki printer: Turn the power off. Tear off any unprinted forms. Remove the Input Tray and Rear Cover together. Raise each Pin Tractor cover and remove the forms from the Pin Tractors. Rotate the Platen Knob and remove the forms from the front of the printer. Place two or three forms in a stack on the Pin Tractors and turn the Platen Knob to push any remaining fragments out of the printer. Replace the Input Tray and Rear Cover. Turn the power on.
How to fix the Oki ML1120 Printer when paper has run out?
If the Oki Printer is out of paper, add more paper and then press the SEL button.
Why is there paper distortion on Oki ML1120 Printer?
If you're experiencing paper distortion with your Oki printer, ensure that sheets are loaded to the end and inserted straight. Also, check for wrinkles, folds, or other defects in the paper and change the paper if necessary. Finally, make sure you're using paper types specified for the printer.
What to do if Oki Printer receives print data but no paper is fed?
If your Oki printer receives print data but doesn't start printing because no paper is being fed, insert paper into the printer.
What to do if Oki Printer printing cannot be resumed?
If printing cannot be resumed on your Oki printer, turn the power OFF, verify that the carriage moves properly, then turn the power ON again. If the problem persists, contact your dealer.
What to do when Oki ML1120 Printer prints content of a single sheet on two sheets when using cut sheets?
If your Oki printer is printing the content of a single cut sheet across two sheets, match the paper setting selected in the application with the physical paper in use. Also, leave enough top and bottom margin in the application. Finally, correct the cut sheet LF adjustment.
What to do if Oki Printer characters are too pale?
If the characters printed by your Oki printer are too pale, first ensure that the Paper Thickness lever position matches the paper type. If it is set correctly, check if the printer is set to print at high speed and set the speed to normal. If the issue persists, the ribbon may be at the end of its life or not installed correctly; try replacing or reinstalling the ribbon cartridge. The ribbon may also be wound incorrectly or not transferring properly, in which case, replace the ribbon cartridge.
What to do if Oki ML1120 prints content of a single form on two forms when using continuous forms?
If your Oki printer is printing the content of a single continuous form across two forms, ensure that the paper length selected in the application matches the physical paper length you are using.
General| Noise level | 49.7 dB |
|---|---|
| Maximum duty cycle | 18000 pages per month |
| Maximum number of copies | 9 copies |
| Power requirements | 120 - 220V |
| Dimensions (WxDxH) | 889 x 587 x 379 mm |
Weight and Dimensions| Dimensions (W x D x H) (imperial) | 35 x 23.1 x 14.9 \ |
|---|
To Next Page
