What to do if Omron SYSDRIVE 3G3JV motor stops during acceleration?
If the motor stops during acceleration or when a load is connected to your Omron Inverter, the load might be too big. Try lengthening the acceleration time or reducing the load. You might also need to increase the motor capacity.
What to do if Omron SYSDRIVE 3G3JV Inverter is not in RUN mode?
If your Omron Inverter isn't in RUN mode, cancel the RUN command, then press the Mode Key to change the Inverter's mode. Restart the Inverter when the green indicator is lit.
Why Omron SYSDRIVE 3G3JV Inverter motor does not operate with correct frequency reference?
If the motor does not operate with input through the control circuit terminals on your Omron Inverter and the frequency reference is zero or different from the set value, check that the setting in n03 for frequency reference selection coincides with the actual method of giving frequency instructions.
Why display does not change when Increment or Decrement Key is pressed on Omron Inverter?
If the display doesn't change when you press the Increment or Decrement Key on your Omron Inverter, it could be due to parameter write-prohibit being active. Set n01 to an appropriate value according to the parameter you want to set. Alternatively, the Inverter might be operating. Turn the Inverter off before making any settings.
How to enable reverse rotation on Omron SYSDRIVE 3G3JV Inverter?
If your Omron Inverter motor only rotates in one direction, reverse rotation-prohibit might be selected. To enable both forward and reverse rotation, set n05 to 0.
What to do if preset output frequency exceeds the upper-limit frequency on Omron SYSDRIVE 3G3JV Inverter?
If the preset output frequency exceeds the upper-limit frequency on your Omron Inverter, make sure that the parameters in n09 and n30 are correct.
How to raise the frequency reference on Omron SYSDRIVE 3G3JV Inverter?
If the frequency reference is too low on your Omron Inverter, raise the frequency reference to at least the minimum output frequency.
What to do if Omron SYSDRIVE 3G3JV Inverter has incorrect sequence input?
If you're inputting a 2-wire sequence while 3-wire sequence is in effect (or vice versa) on your Omron Inverter, check and correct the setting in n37 or change the input method of the RUN command.
What to do if the load is too big for Omron SYSDRIVE 3G3JV?
If the load is too big for your Omron Inverter, reduce the load amount by either reducing the load or lengthening the acceleration/deceleration time.
What to do if Omron SYSDRIVE 3G3JV Inverter ambient temperature is too high?
If the ambient temperature is too high for your Omron Inverter, lower the ambient temperature of the motor to within the acceptable ambient operating temperature range.
General| Model | SYSDRIVE 3G3JV Series |
|---|---|
| Category | Inverter |
| Output Frequency Range | 0.1 to 400Hz |
| Frequency Range | 50/60Hz |
| Control Method | PWM Control |
| Overload Capacity | 150% for 1 minute |
| Protection Features | Overcurrent, Overvoltage, Undervoltage, Overheat |
| Cooling Method | Fan Cooling |
| Ambient Temperature | -10 to 50°C |
| Operating Temperature | -10 to 50°C |
| Storage Temperature | -20°C to +65°C |
| Humidity | 90% RH or less (non-condensing) |
| Altitude | 1000m or less |
| Vibration | 5.9 m/s² or less |
| Braking Unit | Built-in |
| Communication | RS-485 |
| Voltage Class | 200V class, 400V class |
| Input Voltage | 3-phase 200 to 240V AC, 3-phase 380 to 480V AC |
To Next Page