Oriental motor BLH Series Operating Manual

Oriental motor BLH Series

68 pages

To Next Page

To Next Page

Page #1 background image

Loading...

Page #1 background image

HP-5074-9

Brushless Motor

BLH

Series

Digital Setting Type

OPERATING MANUAL

Thank you for purchasing an Oriental Motor product.

This Operating Manual describes product handling procedures and safety precautions.

•

Please read it thoroughly to ensure safe operation.

•

Always keep the manual where it is readily available.

Table of Contents

Other manuals for Oriental motor BLH Series

User Manual148 pages

Questions and Answers:

S
Stephen JonesAug 28, 2025
What to do if Oriental motor BLH Engine does not rotate?
- M
  michelle61Aug 28, 2025
  If the Oriental motor Engine does not rotate, several issues could be the cause. First, check the power supply connection to ensure it is correct. Next, verify that the operation input signal is turned ON, using the internal I/O monitor or D-I/O monitor to check the signal input status. Also, confirm that the correct operation data number is selected and that the motor connector is properly connected. If an alarm is present (PWR/ALM LED blinks red), check the alarm content by counting the LED blinks or using the MEXE02. Finally, ensure the operation data is set correctly, using the status monitor to check the setting method and value.
A
Austin PerezAug 27, 2025
What does it mean when PWR/ALM LED blinks orange on Oriental motor BLH Engine?
- M
  Mr. Christopher WhiteAug 28, 2025
  If the PWR/ALM LED blinks in orange on the Oriental motor Engine, check the generated information using the information monitor or internal I/O monitor, and clear the cause of generation or disable the "INFO action" parameter because information is present.
A
Amy SpencerAug 27, 2025
Why torque cannot be limited on Oriental motor BLH Engine?
- J
  Jody CunninghamAug 27, 2025
  If torque cannot be limited on the Oriental motor Engine, check the connection and the ON-OFF status of the signal. The signal input status can be checked using the internal I/O monitor or D-I/O monitor. If the TL input is turned OFF, the torque limiting function is disabled.
C
claymichaelAug 26, 2025
Why is Oriental motor BLH Engine rotating in the opposite direction?
- K
  Kelly WebbAug 27, 2025
  If the Oriental motor Engine rotates in the opposite direction, check the following: * The ON-OFF operation of the FWD/REV input might be used incorrectly, or the FWD/REV input might not be connected correctly. Check the connection and the ON-OFF status of the signal, using the internal I/O monitor or D-I/O monitor. * The setting of the "Motor rotation direction" parameter may have been changed. The motor rotates forward when the FWD/REV input is ON. The forward rotation setting can be configured with the "Motor rotation direction" parameter (initial value: +=CW).
W
William GibbsAug 25, 2025
Why is the stopping time long for my Oriental motor Engine?
- S
  Stephanie SullivanAug 26, 2025
  If the stopping time is long for the Oriental motor Engine, and the stopping method is wrong, consider these solutions: * Check the stopping method. In the 3-wire mode, stopping by turning the RUN/BRAKE input OFF differs from turning the START/STOP input OFF. In the 2-wire mode, stopping when the STOP-MODE input is ON differs from when it is OFF. * The load inertia may be too large. Increase the frictional load or reduce the load inertia.

Oriental motor BLH Series Specifications

General

Brand	Oriental motor
Model	BLH Series
Category	Engine
Language	English

Related product manuals

Oriental motor BLHD15K

Oriental motor BLHD50K

Oriental motor BLVD40NM

Oriental motor BLHD100K

Oriental motor BLVD20KM

Oriental motor BLH2D15-K

Oriental motor BLED6AM-R

Oriental motor BLE2D60-C

Oriental motor BLE2D30-C

Oriental motor BLE2D400-S

Oriental motor BLE2D120-C

Oriental motor BLE2D200-C