Panasonic AG-CPD20P - Administrator Setup - Trigger Configuration; Enabling and Disabling Triggers; Trigger Action, Detection, and Display

86
87
Administrator Setup
(continued)
Trigger
Trigger
Use this function to turn trigger on or off.
Setting : ON, OFF
Trigger1 to 16
< Action >
Enter actions for detection of trigger signals (GPI1–16). Enter
“NONE” for triggers that will not be used.
REC :
Record
STOP :
Stop
AUTO ZOOM :
Automatically zooms in/out or pauses
P1, P2
*
1
, P3
*
1
: Selects video set for Preset1,
Preset2, or Preset3
P1REC, P2REC
*
1
, P3REC
*
1
: Records video set for Preset1,
Preset2, or Preset3
AUDIO2ON : Records audio input to the [AUDIO
IN 2] connector
AUDIO2MUTE : Not records audio input to the [AUDIO
IN 2] connector
TGT(REC)
*
2
: Starts recording with a TGT input
signal
TGT(P1REC)
*
2
, TGT(P2REC)
*
1
,
*
2
, TGT(P3REC)
*
1
,
*
2
: Starts recording video set for Preset1,
Preset2, or Preset3 with a TGT input
signal
OWN(REC)
*
2
: Starts recording with an OWN input
signal
OWN(P1REC)
*
2
, OWN(P2REC)
*
1
,
*
2
, OWN(P3REC)
*
1
,
*
2
: Starts recording video set for
Preset1, Preset2, or Preset3 with an
OWN input signal
CAM1 LED : Changes the status setting (on/off) of
the [REC] lamp on a Color Camera
connected to the [CAMERA 1]
connector
NONE :
No operation
Note:
When you switch the preset mode, noise may occur in video.
< Detection >
Enter conditions for detection of trigger signals (GPI1–16).
Choice of detection method depends on the setting selected
by <Action>.
In REC, P1REC, P2REC, and P3REC modes
H :
High-edge trigger
Level H :
High-level trigger
L :
Low-edge trigger
Level L :
Low-level trigger
B :
Both-edge trigger
In P1, P2, P3, CAM1 LED, AUDIO2ON, AUDIO2MUTE,
AUTO ZOOM, and STOP modes
H :
High-edge trigger
L :
Low-edge trigger
B :
Both-edge trigger
In NONE mode
H :
High-edge trigger
L :
Low-edge trigger
In TGT(REC), TGT(P1REC), TGT(P2REC), TGT(P3REC),
OWN(REC), OWN(P1REC), OWN(P2REC), and
OWN(P3REC) modes
Setting: OFF, 200, …, 2, 1
< Display >
Assign characters to be used in the Embedded OSD display.
Setting: OFF (no display), A to Z, –
Note:
The value set by <Display> appears when the state triggered
by <Detection> prevails. However, only when a value “B” is
set for <Detection>, the value set by <Display> will appear
during a high state.
•
•
•
•
*
1 These are not displayed if Preset 2 and Preset 3 have not been
set on Video Allocation screen.
*
2 TGT(REC), TGT(P1REC), TGT(P2REC), TGT(P3REC),
OWN(REC), OWN(P1REC), OWN(P2REC), and OWN(P3REC)
can be selected for Trigger 15 and Trigger 16.