Panasonic HEVC Advance AW-UE160WP - Page 121

3G SDI Out1
Make the settings for output from the 3G SDI OUT1 connector.
Format Select
Set the output format.
The following formats can be set depending on the settings in
[Format] in [Basic Config].
Frequency System Format
Format
(3G SDI Out1)
60Hz 2160/60p 1080/60p
1080/60p 1080/60p
59.94Hz 2160/59.94p 1080/59.94p
*
1
1080/59.94i
*
1
2160/29.97p 1080/29.97p
1080/119.88p 1080/59.94p
*
3
1080/59.94p 1080/59.94p
1080/59.94i
1080/29.97p 1080/29.97p
720/59.94p 720/59.94p
50Hz 2160/50p 1080/50p
*
2
1080/50i
*
2
2160/25p 1080/25p
1080/100p 1080/50p
*
3
1080/50p 1080/50p
1080/50i
1080/25p 1080/25p
720/50p 720/50p
24Hz 2160/24p 1080/24p
1080/24p 1080/24p
23.98Hz 2160/23.98p 1080/23.98p
1080/23.98p 1080/23.98p
*
1
When [UHD Crop] is [Crop(720)], output is 720/59.94p.
*
2
When [UHD Crop] is [Crop(720)], output is 720/50p.
*
3
For 119.88p (or 100p), "Frame 1" is output with the frame rate cut
to half (59.94p (
or 50p)).
Factory settings: 1080/59.94p or 1080/50p
HDR OUTPUT SELECT
[SDR(709), HDR(709), HDR(2020)]
Select the signal output when [HDR] is [On].
SDR(709) Selects the SDR output signal.
HDR(709) Selects the HDR output signal (BT.709 equivalent color
gamut).
HDR(2020) Selects the HDR output signal (BT.2020 equivalent color
gamut).
Factory settings: HDR(2020)
<NOTE>
• This cannot be set when the [Basic Config] – [HDR] is [Off].
• [HDR(2020)] can be selected only when [Basic Config] – [GAMUT]
is [WIDE_G2].
V-LOG OUTPUT SELECT [V-LOG, V-709]
Select the signal output when [V-LOG] is [On].
V-LOG Output with a gamma curve that has a wide range of
tones and latitude (exposure range).
V-709 Converted for output to images suited to previewing.
Factory settings: V-LOG
<NOTE>
• This cannot be set when the [Basic Config] – [V-LOG] is [Off].
Output Item [Menu Only, Status]
Select the type of OSD to be superimposed on output video.
Menu Only Displays the OSD menu only.
Status Displays the OSD menu and OSD status.
Factory settings: Menu Only
CHAR [Off, On]
Set whether to superimpose the OSD.
Factory settings: On
3G SDI [LEVEL-A, LEVEL-B]
When [Format Select] (3G SDI Out1) is [1080/59.94p], [1080/60p] or
[1080/50p], select the format for outputting 3G SDI signals.
Factory settings: LEVEL-A
<NOTE>
• [3G SDI] cannot be changed if [Format Select] (3G SDI Out1) is
other than [1080/59.94p], [1080/60p] or [1080/50p].
121
Web screen configurations (continued)