DOWNCON SETTING
Adjust the contours and colors of images down-converted from 4K to
HD.
This is enabled when [FORMAT] is one of the following:
2160/59.94p, 2160/29.97p, 2160/23.98p, 2160/24p, 2160/50p,
2160/25p
<NOTE>
• For all of the DOWNCON SETTING items, setting is not possible
when [V-LOG] is [ON] and [V-LOG PAINT SW] is [OFF].
CHROMA
CHROMA LEVEL SW [OFF, ON]
Set ON/OFF for the chroma level control.
CHROMA LEVEL [–100% to 40%]
Set here the color intensity (chroma level) of the images.
DETAIL SETTING
DETAIL [OFF, ON]
Turn ON/OFF the contour (sharpness of images) adjustment of
images.
MASTER DETAIL [–31 to +31]
Adjust the contour correction level (master).
This is only enabled when [DETAIL] is set to [ON].
H DETAIL LEVEL [00 to 63]
Adjust the level of detail horizontally.
This is only enabled when [DETAIL] is set to [ON].
V DETAIL LEVEL [00 to 63]
Make adjustments vertically to the contour correction level.
This is only enabled when [DETAIL] is set to [ON].
PEAK FREQUENCY [12.4MHz to 37.1MHz]
Set the boost frequency of detail.
This is only enabled when [DETAIL] is set to [ON].
V DETAIL FREQUENCY [00 to 31]
Set the boost frequency of detail (vertically).
00: Low frequency
to
31: High frequency
When a high frequency is selected, the detail effect is added to
subjects with more definition.
This is only enabled when [DETAIL] is set to [ON].
CRISP [00 to 63]
Set the level of noise reduction for the detail signal.
This is only enabled when [DETAIL] is set to [ON].
DETAIL CLIP(+) [00 to 63]
Set the level of clipping of the detail signal in the plus direction
(brighter direction).
This is only enabled when [DETAIL] is set to [ON].
DETAIL CLIP(–) [00 to 63]
Set the level of clipping of the detail signal in the minus direction
(darker direction).
This is only enabled when [DETAIL] is set to [ON].
KNEE APERTURE LEVEL [00 to 39]
Adjust the level of detail for very bright parts.
This is only enabled when [DETAIL] is set to [ON].
DETAIL SETTING
<NOTE>
• For all of the DETAIL SETTING items, setting is not possible when
[V-LOG] is [ON] and [V-LOG PAINT SW] is [OFF].
DETAIL [OFF, ON]
Turn ON/OFF the contour (sharpness of images) adjustment of
images.
MASTER DETAIL [–31 to +31]
Adjust the contour correction level (master).
This is only enabled when [DETAIL] is set to [ON].
PEAK FREQUENCY [1 to 8]
Set the boost frequency of detail.
This is only enabled when [DETAIL] is set to [ON].
CRISP [00 to 63]
Set the level of noise reduction for the detail signal.
This is only enabled when [DETAIL] is set to [ON].
DETAIL GAIN(+) [–31 to +31]
Set the detail level of the plus direction (direction to be made
brighter).
This is only enabled when [DETAIL] is set to [ON].
DETAIL GAIN(–) [–31 to +31]
Set the detail level of the minus direction (direction to be made
darker).
This is only enabled when [DETAIL] is set to [ON].
DETAIL CLIP(+) [00 to 63]
Set the level of clipping of the detail signal in the plus direction
(brighter direction).
This is only enabled when [DETAIL] is set to [ON].
DETAIL CLIP(–) [00 to 63]
Set the level of clipping of the detail signal in the minus direction
(darker direction).
This is only enabled when [DETAIL] is set to [ON].
KNEE APERTURE LEVEL [00 to 39]
Adjust the level of detail for very bright parts.
This is only enabled when [DETAIL] is set to [ON].
DETAIL KNEE [00 to 15]
Adjust the detail component of knee.
This is only enabled when [DETAIL] is set to [ON].
LEVEL DEPENDENT SW [OFF, ON]
Set ON/OFF for the level of reduction in detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
LEVEL DEPENDENT [00 to 15]
Set the level of reduction in detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
DARK DETAIL SW [OFF, ON]
Set ON/OFF for the control that adds detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
DARK DETAIL [0 to 7]
Set the level of detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
64
Camera menu items (continued)
To Next Page
Loading...
