Panasonic HEVC Advance AW-UE160WP - Page 65

DETAIL KNEE [00 to 15]
Adjust the detail component of knee.
This is only enabled when [DETAIL] is set to [ON].
LEVEL DEPENDENT SW [OFF, ON]
Set ON/OFF for the control that reduces detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
LEVEL DEPENDENT [00 to 15]
Set the level of reduction in detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
DARK DETAIL SW [OFF, ON]
Set ON/OFF for the control that adds detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
DARK DETAIL [0 to 7]
Set the level of detail in dark parts.
This is only enabled when [DETAIL] is set to [ON].
SKIN TONE DETAIL SETTING
<NOTE>
• For all of the SKIN TONE DETAIL SETTING items, setting is not
possible when [V-LOG] is [ON] and [V-LOG PAINT SW] is [OFF].
SKIN TONE DETAIL [OFF, ON]
This function smooths skin and produces a more beautiful image.
Set ON/OFF for the skin tone detail function.
MEMORY SELECT [A, B, C]
Select the skin tone table of the subject for the skin tone effect.
ZEBRA [OFF, ON]
Set ON/OFF for the zebra display of the skin tone area.
The zebra pattern is displayed only on devices connected to the
3G SDI OUT2/PM connector.
<NOTE>
• This cannot be set when [ZEBRA] in [SKIN TONE DETAIL
SETTING] is [ON].
ZEBRA EFFECT MEMORY
[A, B, C, A+B, A+C, B+C, A+B+C]
Select the skin tone table for the zebra display.
SKIN TONE EFFECT MEMORY
[A, B, C, A+B, A+C, B+C, A+B+C]
Select the skin tone table for the skin tone effect.
SKIN TONE CRISP [0 to 8]
Adjust the skin tone detail.
I CENTER [000 to 255]
Set the central position above the I axis (area where skin tone is to
take effect).
I WIDTH [000 to 255]
Set the width of the area where the skin tone is to take effect above
the I axis, centered on [I CENTER].
Q WIDTH [000 to 127]
Set the width of the area where the skin tone is to take effect above
the Q axis, centered on [I CENTER].
Q PHASE [0 to 359]
Set the phase of the area where skin tone is to take effect based on
the Q axis.
SKIN TONE DETAIL SETTING
<NOTE>
• For all of the SKIN TONE DETAIL SETTING items, setting is not
possible when [V-LOG] is [ON] and [V-LOG PAINT SW] is [OFF].
SKIN TONE DETAIL [OFF, ON]
This function smooths skin and produces a more beautiful image.
Set ON/OFF for the skin tone detail function.
MEMORY SELECT [A, B, C]
Select the skin tone table of the subject for the skin tone effect.
ZEBRA [OFF, ON]
Set ON/OFF for the zebra display of the skin tone area.
The zebra pattern is displayed only on devices connected to the
3G SDI OUT2/PM connector.
<NOTE>
• This cannot be set when [ZEBRA] in [DOWNCON SETTING] is
[ON].
ZEBRA EFFECT MEMORY
[A, B, C, A+B, A+C, B+C, A+B+C]
Select the skin tone table for the zebra display.
SKIN TONE EFFECT MEMORY
[A, B, C, A+B, A+C, B+C, A+B+C]
Select the skin tone table for the skin tone effect.
SKIN TONE CRISP [–63 to 0 to +63]
Adjust the skin tone detail.
I CENTER [000 to 255]
Set the central position above the I axis (area where skin tone is to
take effect).
I WIDTH [000 to 255]
Set the width of the area where the skin tone is to take effect above
the I axis, centered on [I CENTER].
Q WIDTH [000 to 255]
Set the width of the area where the skin tone is to take effect above
the Q axis, centered on [I CENTER].
Q PHASE [0 to 359]
Set the phase of the area where skin tone is to take effect based on
the Q axis.
65
Camera menu items (continued)