Panasonic KV-S2065L - Page 186

CN515(POINTER DETECTOR) - CN516(ENDING[REAR])
CN517(ENDING[REAR]) - CN518(PAPER JAM[LED])
Pin No. Signal Name Description
1 GND Ground
2 +5V +5V
3 US2 Ground
4 US1 Ultrasonic Waves Output
5 SKEWR Skew (R) Sensor Input
6 AN1 Waiting Sensor Input
7 SKEWL Skew (L) Sensor Input
CN524(STARTING POSITION) - CN525(WAITING)
Pin No. Signal Name Description
1 - N.C.
2 GREEN Green
3 GND Ground
4 RED Red
5 - N.C.
CN372(DRIVE) - (CIS [BACK])
Pin No. Signal Name Description
3 CA
4 *CB
5 CCOMB
6 CB
Pin No. Signal Name Description
1 GND Ground
2 +5V +5V
3 EXIT R Ending (Rear) Position Sensor
4 JAM LED Paper JAM LED Output
5 - N.C.
6 - N.C.
Pin No. Signal Name Description
1 +5V +5V
2 - N.C.
3 - N.C.
4 EXIT(REAR LED) Ending (Rear) Position LED
CN520(STARTING POSITION[LED]) - CN521(ENDING
[REAR])
Pin No. Signal Name Description
1 +5V +5V
2 - N.C.
3 - N.C.
4 EXIT F(LED) Ending (Front) Position LED
CN527(JAM) - CN528(ENDING[FRONT LED])
CN530(POST IMPRINTER DOOR) - CN2011(MOTHER)
Pin No. Signal Name Description
1 +24V3 +24V
2 +24V2 +24V
3 +24V2 +24V
4 +24V1 +24V
CN332(DRIVE) - DOOR SW
Pin No. Signal Name Description
1 *CA Conveyor Motor Phase-A(-)
2 CCOMA +24V for Conveyor Motor
CN341(DRIVE) - Conveyor Motor
Pin No. Signal Name Description
1 *FA
2 -
3 FCOMA
4 FA
5 *FB
6 FCOMB
7 FB
CN351(DRIVE) - Paper Feed Motor
Pin No. Signal Name Description
1 GREEN Green
2 GND Ground
3 RED Red
4 -
CN371(DRIVE) - (CIS [FRONT])
CN802(POWER) - CN861(DC-DC COVERTER)
Pin No. Signal Name Description
1 NEUTRAL Neutral
2 - N.C.
3 LIVE Live
CN801(POWER) - Power Switch
Pin No. Signal Name Description
1
+24V OVP +24V
2 -
3 FAN Fan
CN803(POWER) - Fan
Pin No. Signal Name Description
1
2
3
4
CN531(SIZE) - DOC Sensor
Pin No. Signal Name Description
1 -5V OVP -5V Over Voltage Detection
2 +3.3V OVP +3.3V Over Voltage Detection
3 +5V OVP +5V Over Voltage Detection
4 GND Ground
5 GND Ground
6 GND Ground
7 +24V(SWITCHED) +24V(Switched)
8 +24V(SWITCHED) +24V(Switched)
9 +24V +24V
10 +24V +24V
11 STB +24V Enable
Pin No. Signal Name Description
1 GND Ground
2 +5V
3 JAM(LED) Paper JAM LED Output
4 -
5 - N.C.
+5V
N.C.
Pin No. Signal Name Description
1 +5V +5V
2 -
3 POST DOOR Post Imprinter Door Sensor
4 -
5 GND Ground
N.C.
N.C.
Conveyor Motor Phase-A
Conveyor Motor Phase-B(-)
+24V for Conveyor Motor
Conveyor Motor Phase-B
Feed Motor Phase-A(-)
+24V for Feed Motor
Feed Motor Phase-A
Feed Motor Phase-B
24V for Feed Motor
Feed Motor Phase-B
+5V +5V
DOC DOC Sensor Output
GND Ground
FG Frame Ground