152 VQT2R24 VQT2R24 153
Meanings of and required responses to major messages displayed on LCD monitor.
Message displays
[THIS MEMORY CARD CANNOT BE USED]
●
A MultiMediaCard was inserted.
→ Not compatible with the camera. Use a compatible card.
[THIS MEMORY CARD IS WRITE-PROTECTED]
●
Unlock the write-protect switch on the card. (→16)
[NO VALID PICTURE TO PLAY]
●
Take pictures, or insert a different card already containing pictures.
[THIS PICTURE IS PROTECTED]
●
Release the protection before deleting, etc. (→132)
[SOME PICTURES CANNOT BE DELETED] [THIS PICTURE CANNOT BE DELETED]
●
Non-DCF pictures (→44) cannot be deleted.
→
Save needed data on a computer or other device, and then use [FORMAT] on the camera to
erase the card. (→28)
[NO ADDITIONAL SELECTIONS CAN BE MADE]
●
The number of pictures that can be deleted at once has been exceeded.
●
More than 999 pictures have been set as favourites. (Other than AVCHD Lite motion pictures )
●
The number of pictures allowing [TITLE EDIT], [TEXT STAMP] or [RESIZE] (multiple settings) at
once has been exceeded.
[CANNOT BE SET ON THIS PICTURE]
●
DPOF settings, [TITLE EDIT], or [TEXT STAMP] cannot be made for non-DCF pictures (→44).
[PLEASE TURN CAMERA OFF AND THEN ON AGAIN] [SYSTEM ERROR]
●
The lens is not working correctly.
→ Turn on power again.
(Consult the dealer or your nearest Service Centre if display still remains)
[SOME PICTURES CANNOT BE COPIED] [COPY COULD NOT BE COMPLETED]
●
Pictures cannot be copied in following cases.
→ Picture of same name already exists in built-in memory when copying from card.
→ File is not of DCF standard.
→ Picture taken or edited on a different device.
[NOT ENOUGH SPACE ON BUILT-IN MEMORY] [NOT ENOUGH MEMORY ON THE CARD]
●
There is no space left on the built-in memory or the card. When you copy pictures from the built-in
memory to the card (batch copy), the pictures are copied until the capacity of the card becomes full.
[BUILT-IN MEMORY ERROR] [FORMAT BUILT-IN MEMORY?]
●
Displayed when formatting built-in memory via computer, etc.
→ Reformat directly using camera. Data will be deleted.
[MEMORY CARD ERROR] [FORMAT THIS CARD?]
●
The card format cannot be used with this camera.
→ Save needed data on a computer or other device, and then use [FORMAT] on the camera. (→28)
[INSERT SD CARD AGAIN] [TRY ANOTHER CARD]
●
Access to card has failed.
→ Insert card again.
●
Try with a different card.
[MEMORY CARD ERROR] [MEMORY CARD PARAMETER ERROR]
●
Card is not of SD standard.
●
When cards in capacities of 4 GB or more are used, only SDHC or SDXC memory cards are
supported.
[READ ERROR]/[WRITE ERROR] [PLEASE CHECK THE CARD]
●
Data read has failed.
→ Check whether card has been inserted correctly (→14).
●
Data write has failed.
→ Turn off power and remove card, before re-inserting and turning on power again.
●
Card may possibly be damaged.
●
Try with a different card.
[MOTION RECORDING WAS CANCELLED DUE TO THE LIMITATION OF THE WRITING
SPEED OF THE CARD]
●
Using a card of SD speed ‘Class 4’* or above is recommended for recording motion pictures in
‘AVCHD Lite (GPS)’ /‘AVCHD Lite’.
Using a card of SD speed ‘Class 6’* or above is recommended for recording motion pictures in
‘MOTION JPEG’.
∗
The SD speed class is a speed rating for continuous writing.
●
If recording stops even when using the card above, the data writing speed is low. We recommend
backing up the data on the memory card and reformatting it (→28).
●
Motion picture recording may be automatically terminated with certain cards.
[A FOLDER CANNOT BE CREATED]
●
Folder numbers in use have reached 999.
→ Save all necessary data to computer (or other device), and [FORMAT] (→28).
Folder number is reset to 100 when performing [NO.RESET] (→25).
[PICTURE IS DISPLAYED FOR 16:9 TV] [PICTURE IS DISPLAYED FOR 4:3 TV]
●
AV cable is connected to camera.
→ To remove message immediately → Press [MENU/SET].
→ To change aspect ratio → Change [TV ASPECT] (→26).
●
USB connection cable is only connected to camera.
→ Message disappears when cable is also connected to another device.
[THIS BATTERY CANNOT BE USED]
●
Use a genuine Panasonic battery.
●
Battery cannot be recognised as terminal is dirty.
→ Wipe any dirt away from the battery terminal.
[NO BATTERY POWER REMAINS]
●
The battery level is low.
→ Charge the battery before use. (→11)
To Next Page
Loading...
Need help?
General
Weight and Dimensions
