Parker AC10 series User Manual

15-10 Parameter Reference
AC10 Inverter
Multi-stage Speed Control: F500-F580
Function
Code
Function
Definition
Setting Range
Mfr’s Value
Change
F500
Stage speed type
0: 3
-stage speed;
1: 15
-stage speed;
2: Max 8
-stage speed auto circulating
1
╳
F501
Selection of Stage Speed
Under
Auto
-circulation Speed Control
2
～8
7
√
F502
Selection of
Times of Auto- Circulation
Speed Control
0
～9999（when the value is set to 0, the
inverter will carry out infinite circulating
）
0
√
F503
Status after
auto circulation running
Finished
0: Stop
1: Keep running at last stage speed
0
√
F504
Frequency setting for stage 1 speed
F112
～F111
5.00Hz
√
F505
Frequency setting for stage 2 speed
F112
～F111
10.00Hz
√
F506
Frequency setting for stage 3 speed
F112
～F111
15.00Hz
√
F507
Frequency setting for
stage 4 speed
F112
～F111
20.00Hz
√
F508
Frequency setting for stage 5 speed
F112
～F111
25.00Hz
√
F509
Frequency setting for stage 6 speed
F112
～F111
30.00Hz
√
F510
Frequency setting for stage 7 speed
F112
～F111
35.00Hz
√
F511
Frequency setting for stage 8
speed
F112
～F111
40.00Hz
√
F512
Frequency setting for stage 9 speed
F112
～F111
5.00Hz
√
F513
Frequency setting for stage 10 speed
F112
～F111
10.00Hz
√
F514
Frequency setting for stage 11 speed
F112
～F111
15.00Hz
√
F515
Frequency setting for stage 12 speed
F112
～F111
20.00Hz
√
F516
Frequency setting for stage 13 speed
F112
～F111
25.00Hz
√
F517
Frequency setting for stage 14 speed
F112
～F111
30.00Hz
√
F518
Frequency setting for stage 15 speed
F112
～F111
35.00Hz
√
F519
-
F533
Acceleration time setting for the
speeds from
Stage 1
to stage 15
0.1
～3000S
Subject to
inverter model
√
F534
-
F548
Deceleration time setting for the speeds f
rom
Stage 1
to stage 15
0.1
～3000S
√
F549
-
F556
Running directions of stage speeds f
rom
Stage 1
to stage 8
0:
Forward running;
1:
Reverse running
0
√
F557
-
F564
Running time of stage speeds f
rom
Stage 1
to stage 8
0.1
～3000S
1.0S
√
F565
-
F572
Stop time after finishing stages f
rom
Stage
1
to stage 8.
0.0
～3000S
0.0S
√
F573
-
F579
Running directions of stage speeds f
rom
Stage
9 to stage 15.
0:
Forward running;
1:
Reverse running
0
√
F580
Reserved
0: Stage speed mode 1
1: Stage speed mode 2
1
√
TC-Hydraulik - Rsdorfer Str. 8 - 25746 Heide - Lars Lornsen - T: +49 481 909 - 34 - l.lornsen@tc-hydraulik.de - www.tc-hydraulik.de

Parker AC10 series Specifications

General

Overload Capacity	150% for 60 seconds
Analog Inputs	2
Analog Outputs	1
Communication Options	Modbus RTU
Protection Rating	IP20
Input Voltage	200-240VAC, 380-480VAC, 500-575VAC, 600VAC, 690VAC
Digital Outputs	2
Protection	Overcurrent, Overvoltage, Undervoltage, Overtemperature, Short Circuit
Operating Temperature	-10°C to +50°C
Humidity	5% to 95% (non-condensing)
Dimensions	Varies by model
Weight	Varies by model
Braking	Built-in dynamic braking