Rigol DS6062-DEMO

To Next Page

To Previous Page

RIGOL

DS6000 User’s Guide

1-5

To Adjust the Supporting Legs

Adjust the supporting legs properly to use them as stands to tilt the oscilloscope

upwards, thus to place the oscilloscope stably and to operate and observe the display

better.

Figure 1-4 To Adjust the Supporting Legs

Main Page

Guaranty and Declaration3
Safety Requirement4
- General Safety Summary4
- Safety Terms and Symbols6
- Measurement Category7
- Ventilation Requirement8
- Working Environment9
- General Care and Cleaning11
- Environmental Considerations12
DS6000 Series Overview13
Document Overview15
- Table of Contents17
1 Quick Start23
- General Inspection24
- Appearance and Dimensions25
- To Prepare the Oscilloscope for Use26
- Front Panel Overview35
- Rear Panel Overview36
- Front Panel Function Overview38
- User Interface45
- To Use the Security Lock50
- To Use the Desk Mount Instrument Arm51
- To Use the Rack Mount Kit52
- To Use the Built-In Help System58
2 To Set the Vertical System59
- To Enable the Channel60
- Channel Coupling61
- Bandwidth Limit62
- Probe62
- Input Impedance64
- Waveform Invert65
- Vertical Scale65
- Vertical Expansion66
- Amplitude Unit66
- Channel Label67
3 To Set the Horizontal System69
- Delayed Sweep70
- Time Base Mode72
- Horizontal Scale77
- Horizontal Reference78
4 To Set the Sample System81
- Acquisition Mode82
- Sample Mode85
  - Real-Time Sample85
  - Equivalent Sample85
- Sample Rate86
- Memory Depth88
- Antialiasing89
5 To Trigger the Oscilloscope91
- Trigger Source92
- Trigger Mode93
- Trigger Coupling95
- Trigger Holdoff96
- Noise Rejection97
- Trigger Type98
- Trigger Ouput Connector120
6 To Make Measurements121
- Math Operation122
- Auto Measurement133
- Cursor Measurement147
7 Protocol Decoding155
- Parallel Decoding156
- RS232 Decoding (Option)158
- SPI Decoding (Option)162
- I2C Decoding (Option)165
- CAN Decoding (Option)167
8 Reference Waveform169
- To Enable REF Function170
- To Select REF Source171
- To Save to Internal Memory171
- To Adjust REF Waveform Display171
- To Export to Internal or External Memory172
- To Import from Internal or External Memory172
9 Pass/Fail Test173
- To Enable Pass/Fail Test Function174
- To Select Source175
- To Create Mask175
- Test and Output175
- To Save the Test Mask176
- To Load the Test Mask176
10 Waveform Recording177
- Waveform Playback180
- Waveform Analysis182
  - Analysis Based on Trace185
  - Analysis Based on Pass/Fail Mask186
11 Display Control187
- To Select the Display Type188
- To Set the Persistence Time189
- To Set the Waveform Brightness191
- To Set the Screen Grid191
- To Set the Grid Brightness191
- To Set the Menu Display191
12 Store and Recall193
- Storage System194
- Storage Type195
- Internal Store and Recall197
- External Store and Recall200
- Disk Management203
- Factory209
13 System Function Setting215
- Remote Interface Configuration216
- System-Related221
- To Print the Waveform232
14 Remote Control237
- Remote Control Via USB238
- Remote Control Via LAN242
- Remote Control Via GPIB245
15 Troubleshooting247
16 Specifications249
17 Appendix257
- Appendix A: Options and Accessories257
- Appendix B: Warranty258
- Appendix C: any Comment or Question259
Index261

Table of Contents

Other manuals for Rigol DS6062-DEMO

Related product manuals