Roland RD-700GX User Manual

172
Effect/Parameter List
72: ENH → CHORUS
(ENHANCER → CHORUS)
This effect connects an enhancer and a chorus in series.
73: ENH → FLANGER
(ENHANCER → FLANGER)
This effect connects an enhancer and a flanger in series.
74: ENH → DELAY (ENHANCER → DELAY)
This effect connects an enhancer and a delay in series.
75: CHO → DELAY (CHORUS → DELAY)
This effect connects a chorus and a delay in series.
76: FLN → DELAY (FLANGER → DELAY)
This effect connects a flanger and a delay in series.
Assignable Parameters
MFX Control
Chorus Bal, Chorus Depth, Cho Rate, Enhancer Sens
Parameter
Value Description
Enhancer Sens 0–127 Sensitivity of the enhancer
Enhancer Mix 0–127
Level of the overtones generated by
the enhancer
Chorus PreDly 0.0–100.0 ms
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note
When this is set to “note,” the effect is
synchronized with the tempo.
Cho Rate(Hz) 0.05–10.00 Hz Frequency of modulation (Hz)
Cho Rate ( ) note (*1) Frequency of modulation (note)
Chorus Depth 0–127 Depth of modulation
Chorus Bal
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
chorus (W) and the sound that is not
sent through the chorus (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control
Flngr Bal, Fln Rate, Flngr Depth, Flngr Feedback, Enhancer
Sens
Parameter
Value Description
Enhancer Sens 0–127 Sensitivity of the enhancer
Enhancer Mix 0–127
Level of the overtones generated by
the enhancer
Flngr PreDly 0.0–100.0 ms
Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
Flngr Mode Hz, note
When this is set to “note,” the effect is
synchronized with the tempo.
Fln Rate(Hz) 0.05–10.00 Hz Frequency of modulation (Hz)
Fln Rate( ) note (*1) Frequency of modulation (note)
Flngr Depth 0–127 Depth of modulation
Flngr Feedback -98– +98%
Adjusts the proportion of the flanger
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Flngr Bal
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the
flanger (W) and the sound that is not
sent through the flanger (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control
Delay Bal, Enhancer Sens
Parameter
Value Description
Enhancer Sens
0–127 Sensitivity of the enhancer
Enhancer Mix 0–127
Level of the overtones generated by
the enhancer
Delay Mode ms, note
When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms)
1–2600 ms
Adjusts the delay time from the direct
sound until the delay sound is heard.
(Hz)
Delay ( ) note (*1)
Adjusts the delay time from the direct
sound until the delay sound is heard.
(note)
Delay Feedback -98– +98%
Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Delay Bal
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the delay
(W) and the sound that is not sent
through the delay (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control
Delay Bal, Chorus Bal, Chorus Depth, Cho Rate
Parameter
Value Description
Chorus PreDly
0.0–100.0 ms
Adjusts the delay time from the direct
sound until the chorus sound is heard.
Rate Mode Hz, note
When this is set to “note,” the effect is
synchronized with the tempo.
Cho Rate(Hz) 0.05–10.00 Hz Frequency of modulation (Hz)
Cho Rate ( ) note (*1) Frequency of modulation (note)
Chorus Depth 0–127 Depth of modulation
Chorus Bal
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the chorus sound (W)
Delay Mode ms, note
When this is set to “note,” the effect is
synchronized with the tempo.
Delay (ms) 1–2600 ms
Adjusts the delay time from the direct
sound until the delay sound is heard.
(Hz)
Delay ( ) note (*1)
Adjusts the delay time from the direct
sound until the delay sound is heard.
(note)
Delay Feedback -98– +98%
Adjusts the proportion of the delay
sound that is fed back into the effect.
Negative (-) settings will invert the
phase.
Delay HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect will be
cut. If you do not want to cut the high
frequencies, set this parameter to
BYPASS.
Delay Bal
D100:0W–
D0:100W
Adjusts the volume balance between
the sound that is sent through the delay
(W) and the sound that is not sent
through the delay (D).
Level 0–127 Output Level
Assignable Parameters
MFX Control
Delay Bal, Flngr Bal, Fln Rate, Flngr Feedback
Parameter
Value Description
Flngr PreDly
0.0–100.0 ms
Adjusts the delay time from when the
direct sound begins until the flanger
sound is heard.
Parameter
Value Description
RD-700GX_e.book 172 ページ ２００８年２月１３日 水曜日 午後５時４９分

Roland RD-700GX Specifications

General

Brand	Roland
Model	RD-700GX
Category	Musical Instrument
Language	English