175
Effect/Parameter List
84: LINEDRIVE
This reproduces the distortion that occurs when an electrical
circuit is slightly overloaded.
85: *STEREO EQ (STEREO EQUALIZER)
This is a four-band stereo equalizer (low, mid x 2, high).
86: *OVERDRIVE
This effect creates a soft distortion similar to that produced by
vacuum tube amplifiers.
Parameter
Value Description
Vib/Cho Switch
OFF, ON
Switches the vibrato and chorus
effects
Vib/Cho Type
V-1, V-2, V-3,
C-1, C-2, C-3
Vibrato and chorus effect types
V-1, V-2, V-3:
Adds a wavering
(vibrato) that is created by changes in
the pitch.
The effect deepens as the value is
increased
C-1, C-2, C-3:
Adds a fullness and
breadth (chorus) to the sound.
The effect deepens as the value is
increased.
Vib/Cho
Vintage
’50, ’60, ’70
This reproduces the subtle differences
in the vibrato and chorus effects in
organs built in different years.
Vib/Cho Level 0–127 Vibrato/chorus effect volume
OD Switch OFF, ON Switches the overdrive effect
OD Drive 0–127 Amount of distortion
OD Level 0–127 Overdrive effect volume
Rotary Switch OFF, ON Switches the rotary effect
Rotary Speed SLOW, FAST
Low– and high-frequency rotation
speeds (Rate)
SLOW
: (Slow Rate)
FAST
: (Fast Rate)
R-Wf Slow Sp 0.05–10.00 Hz
Rate with low-frequency rotor set to
SLOW rate
R-Wf Fast Sp 0.05–10.00 Hz
Rate with low-frequency rotor set to
FAST rate
R-Wf Accel 0–15
Speed at which the low-frequency
rotor’s rotation rate changes when the
rotation speed is switched
R-Wf Level 0–127 Low-frequency rotor volume
R-Tw Slow Sp 0.05–10.00 Hz
High-frequency rotor setting
This parameter is the same as that for
the low-frequency rotor.
R-Tw Fast Sp 0.05–10.00 Hz
R-Tw Accel 0–15
R-Tw Level 0–127
Rotary Separat 0–127 Amount of breadth in the sound
Rotary Level 0–127 Output volume
Assignable Parameters
MFX Control Drive
Parameter
Value Description
Strength
SOFT, HARD
HARD produces stronger distortion
than SOFT.
Type 1/2 Varies the nuances of the distortion.
Drive 0–127
Degree of distortion
This also affects the volume.
Low Gain -15–+15 dB Boost or cut in the low end.
High Gain -15–+15 dB Boost or cut in the high end.
Level 0–127 Output level
Assignable Parameters
MFX Control Level
Parameter Value Description
Low Freq 200, 400 Hz
Select the frequency of the low range
(200 Hz/400 Hz).
Low Gain -15– +15 dB
Adjust the gain of the low frequency.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Freq
2000, 4000,
8000 Hz
Select the frequency of the high range
(2000 Hz/4000 Hz/8000 Hz).
High Gain -15– +15 dB
Adjust the gain of the high frequency.
Positive (+) settings will emphasize
(boost) the high frequency range.
P1 Freq 200–8000Hz
Adjust the frequency of Middle 1 (mid
range).
P1 Q
0.5, 1.0, 2.0,
4.0, 8.0
This parameter adjusts the width of the
area around the Middle 1 Frequency
that will be affected by the Gain
setting. Higher values of Middle 1 Q
will result in a narrower area being
affected.
P1 Gain -15– +15 dB
Adjust the gain for the area specified
by the Middle 1 Frequency and Q
settings.
Positive (+) settings will emphasize
(boost) the Middle 1 range.
P2 Freq 200–8000 Hz
Adjust the frequency of Middle 2 (mid
range).
P2 Q
0.5, 1.0, 2.0,
4.0, 8.0
This parameter adjusts the width of the
area around the Middle 2 Frequency
that will be affected by the Gain
setting. Higher values of Middle 2 Q
will result in a narrower area being
affected.
P2 Gain -15– +15 dB
Adjust the gain for the area specified
by the Middle 2 Frequency and Q
settings.
Positive (+) settings will emphasize
(boost) the Middle 2 range.
Level 0–127 Adjust the output level.
Assignable Parameters
MFX Control
Drive, Amp Type, Pan
Parameter
Value Description
Drive
0–127
Adjust the degree of distortion. The
volume will change together with the
degree of distortion.
Pan L64–0–63R
Adjust the stereo location of the output
sound. L64 is far left, 0 is center, and
63R is far right.
Amp Type
SMALL,
BUILT-IN,
2-STACK,
3-STACK
Select the type of guitar amp.
SMALL
: small amp
BUILT-IN
: single-unit type amp
2-STACK
: large double stack amp
3-STACK
: large triple stack amp
Low Gain -15– +15 dB
Adjust the gain of the low frequency
range.
Positive (+) settings will emphasize
(boost) the low frequency range.
High Gain -15– +15 dB
Adjust the gain of the high frequency
range.
Positive (+) settings will emphasize
(boost) the high frequency range.
Level 0–127
Adjust the output level.
It’s a good idea to use this Parameter
to adjust the difference in volume
between when Overdrive is applied
and when it is not applied.
Parameter Value Description
RD-700GX_e.book 175 ページ ２００８年２月１３日 水曜日 午後５時４９分
To Next Page
Loading...
Need help?
General
