23
Editing a Kit’s Settings (KIT Edit)
Parameter Value Explanation
Low Cut
FLAT, 20Hz,
25Hz, 31.5Hz,
40Hz, 50Hz,
63Hz, 80Hz,
100Hz, 125Hz,
160Hz, 200Hz,
250Hz, 315Hz,
400Hz, 500Hz,
630Hz, 800Hz
Specifies the frequency below which
the low-frequency region of the reverb
is cut.
HighCut
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
Specifies the frequency above which
the high-frequency region of the
reverb is cut.
Density 0–10
Adjusts the density of the reverb
sound.
KIT: DELAY
Parameter Value Explanation
Type
DLY, PAN, TAPE
ECHO
Selects the type of delay.
TempoSync OFF, ON
Choose ON if you want the delay time
to synchronize with the tempo.
Level
DELAY [LEVEL]
OFF, 1–255 Specifies the volume of the delay.
Time
DELAY [TIME]
(TempoSync =
OFF) 0–255
(TempoSync =
ON) 1/32, 1/16T,
1/32D, 1/16,
1/8T, 1/16D, 1/8,
1/4T, 1/8D, 1/4,
1/2T, 1/4D, 1/2,
1/1T, 1/2D, 1/1
Specifies the time by which the sound
is delayed.
Feedback
DELAY [FEEDBACK]
0–255
Adjusts the amount of feedback
(amount of repetition).
DLY, PAN
HighCut
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz,
FLAT
Specifies the frequency above which
the high-frequency region of the delay
sound is cut.
H Damp
0.0dB–-40.0dB
(0.5 dB increments),
-INF
Adjusts the amount by which the
high-frequency region of the delay
sound is cut at each repetition.
H DampF
630Hz, 800Hz,
1kHz, 1.25kHz,
1.6kHz, 2kHz,
2.5kHz, 3.15kHz,
4kHz, 5kHz,
6.3kHz, 8kHz,
10kHz, 12.5kHz
Specifies the frequency above which H
Damp cuts the high-frequency region.
L Damp
0.0dB–-40.0dB
(0.5 dB increments),
-INF
Adjusts the amount by which the low-
frequency region of the delay sound is
cut at each repetition.
Parameter Value Explanation
L DampF
80.0Hz, 100Hz,
125Hz, 160Hz,
200Hz, 250Hz,
315Hz, 400Hz,
500Hz, 630Hz,
800Hz
Specifies the frequency below which L
Damp cuts the low-frequency region.
PAN
Tap Time 0% –100%
Adjusts the delay (tap) time of the
right side, relative to the left side as
100%.
TAP ECHO
Mode
S, M, L, S+M,
S+L, M+L,
S+M+L
Selects the combination of playback
heads.
S (Short), M (Middle), L (Long)
Bass
-15dB–0dB–
+15dB
Adjusts the low-frequency region of
the echo sound.
Treble
-15dB–0dB–
+15dB
Adjusts the high-frequency region of
the echo sound.
Pan S
L127–CENTER–
R127
Specifies the panning of the S (Short)
playback head.
Pan M
L127–CENTER–
R127
Specifies the panning of the M
(Middle) playback head.
Pan L
L127–CENTER–
R127
Specifies the panning of the L (Long)
playback head.
Tape Dist 0–8
Adjusts the amount of distortion for
the echo sound.
W/F Rate 0–255
Adjusts the modulation speed of wow
and flutter.
W/F Depth 0–255 Adjusts the depth of wow and flutter.
KIT: MASTER FX
Parameter Value Explanation
Type
HPF, LPF,
LPF/HPF,
H BOOST,
L BOOST,
L/H BOOST,
ISOLATOR,
TRANSIENT,
TRANSIENT2,
COMPRESSOR,
DRIVE,
OVERDRIVE,
DISTORTION,
FUZZ,
CRUSHER,
PHASER,
FLANGER, SBF,
NOISE
Selects the type of MASTER FX.
HPF: high pass filter
(cuts the low-frequency
region)
LPF: low pass filter (cuts the high-frequency
region)
LPF/HPF: low pass filter / high pass
filter (cuts the high-frequency or low-frequency
region)
H BOOST: high boost (boosts the high-
frequency region)
L BOOST: low boost (boosts the low-frequency
region)
L/H BOOST: low boost / high boost
(boosts the low-frequency or high-frequency region)
ISOLATOR: adjusts the balance of
the low, mid, and high-frequency
regions.
TRANSIENT: strengthens or weakens
the attack and release.
TRANSIENT2: uses the attack and
release to operate a filter.
COMPRESSOR: compresses loud
input, making the maximum levels
more consistent.
DRIVE: uncolored distortion.
OVERDRIVE: overdrive
DISTORTION: distortion
FUZZ: fuzz
CRUSHER: produces a lo-fi effect.
PHASER: produces a phase effect.
FLANGER: produces a flanging effect.
SBF: side band filter
(a filter that passes only
specific frequency components).
NOISE: adds noise.
To Next Page
Loading...
Need help?
General
Weight and Dimensions
