How to fix DOWNLOADER ERROR FLASH NOT ERASED Repeat Download on SATO GL4xxe Barcode Reader?
The SATO Barcode Reader displays 'DOWNLOADER ERROR FLASH NOT ERASED' because the printer encountered an error trying to program flash memory. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
What causes DOWNLOADER ERROR MAIN FLASH IS FULL Optimize Files on SATO Barcode Reader?
The SATO Barcode Reader displays 'DOWNLOADER ERROR MAIN FLASH IS FULL' because an attempt was made to download to a full main flash memory. Delete and optimize files.
What to do when SATO GL4xxe Barcode Reader displays DOWNLOADER ERROR EXTERNAL FLASH IS FULL Optimize Files?
The SATO Barcode Reader displays 'DOWNLOADER ERROR EXTERNAL FLASH IS FULL' because an attempt was made to download to a full EFC. Delete and optimize files.
Why does SATO Barcode Reader show ERROR: WRONG CHECKSUM Repeat Download?
The SATO Barcode Reader displays 'ERROR: WRONG CHECKSUM' because the printer received the complete program but the checksum did not match, indicating data corruption during download. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
How to fix INVALID FILE SYS Optimize&Reboot on SATO GL4xxe Barcode Reader?
The SATO Barcode Reader shows 'INVALID FILE SYS' because the file system was not detected or flash was corrupted. Enter the PRINTER SETUP menu and use the Optimize & Reboot option.
What does CALIBRATION FAIL mean on my SATO GL4xxe?
The SATO Barcode Reader shows CALIBRATION FAIL because calibration values derived from Manual Calibrate were not acceptable. To fix this, perform a Run Manual Cal (run manual calibration) again.
Why does my SATO Barcode Reader display MEDIA OUT COMPATIBLE WITH CUTTER Check Media Mode?
The SATO Barcode Reader shows 'MEDIA OUT COMPATIBLE WITH CUTTER' because Tear-Off or Peel-Off Media Handling selection was attempted with the cutter option still installed. These modes require that the front door assembly be installed to use the Label Taken Sensor. Select a different Media Handling mode.
What does SOFTWARE ERROR Cycle Power mean on SATO GL4xxe Barcode Reader?
The SATO Barcode Reader shows 'SOFTWARE ERROR' because application software tried to perform an illegal power function or there are damaged logic circuits on the main circuit board. Cycle the printer’s power. If possible, print a job that has previously worked. If the problem persists, contact an authorized customer service representative.
Why am I getting ERROR: INSUFFICIENT FLASH on my SATO Barcode Reader?
The SATO Barcode Reader displays 'ERROR: INSUFFICIENT FLASH' because the printer requires more flash memory to download program. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
What causes EC SOFTWARE FAIL error on SATO Barcode Reader?
The SATO Barcode Reader displays 'EC SOFTWARE FAIL' due to engine control software failure. Power off the printer for 15 seconds, then power on again. If the problem persists, contact an authorized customer service representative.
General| Print Method | Thermal Transfer / Direct Thermal |
|---|---|
| Print Resolution | 203 dpi |
| Max. Print Width | 104 mm (4.09 inches) |
| Media Type | Roll, Fanfold, Tag, Ticket |
| Media Width | 25.4 mm - 118 mm (1 inch - 4.65 inches) |
| Media Thickness | 0.06 mm - 0.25 mm (0.0024 inch - 0.0098 inch) |
| Interfaces | USB, Serial, Ethernet, Parallel |
| Barcodes | 1D and 2D barcodes |
| Scanning Technology | N/A (Printer, not a scanner) |
| Scan Rate | N/A (Printer, not a scanner) |
| Resolution | N/A (Printer, not a scanner) |
| Interface | N/A (Printer, not a scanner) |
| Operating Temperature | 5°C - 40°C (41°F - 104°F) |
| Storage Temperature | 14°F to 140°F (-10°C to 60°C) |
| Humidity | 20% - 85% (non-condensing) |
| Lighting | N/A (Printer, not a scanner) |
| Power Supply | AC 100-240 VAC ±10%, 50/60 Hz |
Explains the manual's layout, structure, and use of special information boxes.
Describes the GL4e Series printers, their high-volume labeling applications, and construction.
Identifies interactive control features like LCD display, LED indicators, and operator buttons.
Details printer dimensions, weight, operating, and storage conditions.
Covers power requirements, CPU, ROM, buffer, and interface module details.
Outlines print speed, resolution, media width, length, and ribbon specifications.
Describes media sensing features and regulatory compliance standards.
Lists supported character fonts and barcode types.
Guides on unpacking the printer, identifying parts, and initial physical setup.
Provides guidance on stationing, connecting the printer, and selecting its location.
Details media selection, loading procedures for rolled/fan-fold media, and ribbon loading.
Explains different printer operational modes like Continuous, Tear-Off, Cutter, and Dispense.
Presents interface types and guides on installing interface hardware.
Details the installation process for flash memory cards.
Provides in-depth instructions for printer configuration using the operator panel.
Overviews User Mode, Configuration Mode, Advanced Mode, and various emulation modes.
Explains parameters within User Mode, providing descriptions and factory defaults.
Details various test print options to verify printer operation and quality.
Covers printing the error log and clearing it for troubleshooting.
Shows installed memory, printer usage, and head status.
Allows resetting print statistics and managing head data.
Lists specific error signals, their explanations, and recommended solutions.
Provides a table of common print quality problems and their resolutions.
Offers checklists for diagnosing problems with Parallel, Serial, USB, and other interfaces.
Explains using Hex Dump and Test Labels for identifying print problems.
Details procedures for cleaning debris and residue from the print head and platen roller.
Provides instructions for replacing primary and secondary printer components like the print head and fuse.
Details replacing the media platen roller and positioning the label sensor for accurate media detection.
Covers print head balance, pressure, alignment, and ribbon guide/roller alignment for optimal print quality.
To Next Page
