Sharp MX-C312 User Manual

5-70
SCANNER/INTERNET FAX
Contents
4
Select the erase settings.
(1) Touch the desired erase mode.
Select one of the 2 erase modes.
Touch the [Side Erase] key to open the following screen.
Touch the checkbox of the edge that you wish to erase
and make sure that a checkmark ( ) appears.
When performing two-sided scanning, set the erase edge
on the reverse side.
• If you touch the [Same Side as Side 1] key, the edge in
the same position as on the front side will be erased.
• If you touch the [Different Side from Side 1], the edge in
the position opposite to the erased edge on the front
side will be erased.
When you have completed the settings, touch the [OK] key.
(2) Set the erasure width with the keys.
0 mm to 20 mm (0" to 1") can be entered.
(3) Touch the [OK] key.
5
Press the [COLOUR START] key or the [BLACK & WHITE START] key.
Scanning begins.
• If you inserted the original pages in the document feeder tray, all pages are scanned.
A beep will sound to indicate that scanning is finished.
• If you are scanning the original on the document glass, scan each page one page at a time.
When scanning of one page finishes, replace it with the next page and press the [COLOUR START] key or the [BLACK &
WHITE START] key. Repeat until all pages have been scanned and then press the [Read-End] key.
A beep will sound to indicate that scanning is finished.
If the destination is an Internet fax destination, press the [BLACK & WHITE START] key.
To cancel scanning...
Press the [STOP] key ( ) to cancel the operation.
When the erase function is used, erase takes place at the edges of the original image. If you also use a reduction or an
enlargement setting, the erase width will change according to the selected ratio. For example, if the erase width setting is
20 mm (1") and the image is reduced to 50%, the erase width will be 10 mm (1/2").
To cancel the erase setting...
Touch the [Cancel] key in the screen of step 4.
System Settings (Administrator): Erase Width Adjustment
The default erase width setting is linked to the copy mode system setting, and can be set from 0 mm to 20 mm (0" to 1"). The
factory default setting is 10 mm (1/2").
Scan/Special Modes
OK
Erase
Edge
OKCancel
Side Erase
Edge
Erase
10
(0~20)
mm
(2) (3)(1)
Different Side
from Side 1
Erase
Up
Erase position
for Original Side 2
Same Side as
Side 1
Cancel
Side Erase
Left
Right
Down
OK

Sharp MX-C312 Specifications

Power

power consumption	1.44 kW or less
power source	AC 100-127VAC, 60HZ, 12 AMPS

Copying Features

copy speed	31 ppm B&W/Color
first copy time	8.0 sec or less (B&W); 8.9 sec or less (color)
warm-up time	90 seconds or less

Scanning Features

scan speed	Up to 35 ipm (B&W or color)
optical resolution	600 dpi
output modes	600 dpi, 400 dpi, 300 dpi, 200 dpi, 100 dpi

Network Printing System

print resolution	1200 dpi, 600 dpi
print speed	31 pages per minute (Letter)
resident fonts	80 Outline Fonts

Inner Finisher

output capacity	Up to 280 sheets (Letter/Legal)
weight	Approx. 19.8 lbs
dimensions	18-2/3" (w) x 13-1/16" (d) x 6-3/16" (h)

Weight and Dimensions

weight	102 lbs
dimensions	22-3/64" x 17-1/4" x 28-7/64"