Siei ARTDriveG - Maximum Cable Cross Section for Power Terminals

36 • Chapter 5 - Wiring Procedure ARTDriveG Instruction manual
5.2.1 Maximum Cable Cross Section for Power Terminals
AC input wiring is connected to a disconnected switch, which limits the size to the following ranges:
AGy…-4 (230V…480V) Type 1007 1015 1022 1030 2040 2055 2075 3110 3150 4220 4300
AWG
12 8 4
[mm2]
8 101625
Tightening torque
[Nm]
23
AWG
12 8 6 10 8
[mm2]
810610
Tightening torque
[Nm]
0.9 1.6
AWG
12 8 6
[mm2]
8 101616
Tightening torque
[Nm]
23
AGy…-4 (230V…480V) Type 4370 5450 5550 6750 7900 71100 71320
AWG
1/0 2/0 4/0 300* 350* * = kcmils
[mm2]
50 70 95 150 185
Tightening torque
[Nm]
AWG
8
[mm2]
10
Tightening torque
[Nm]
1.6
AWG
[mm2]
Tightening torque
[Nm]
3
AGy…-5 (575V) Type 2002 2003 2005 3007 3010 3015 3020 4025 4030
AWG
[mm
2
]
Tightening torque
[Nm]
AWG
[mm
2
]
Tightening torque
[Nm]
AWG
[mm
2
]
Tightening torque
[Nm]
AGy…-5 (575V) Type 4040 5050 5060 5075 6100 7125 7150 8200
AWG
6 4 1/0 2/0 4/0 350*
[mm
2
]
16 25 50 70 95 185
Tightening torque
[Nm]
2 4 12 12 10-30
AWG
10 6
[mm
2
]
616
Tightening torque
[Nm]
0.9 3
AWG
[mm
2
]
Tightening torque
[Nm]
agy4040
terminals not available
2
50
42
4
BR1 terminals
PE1, PE2 terminals
6
16
6
16
2
0.5 to 0.6 1.2 to 1.5 2
U1,V1,W1,U2,V2,W2,C,D
terminals
2
35
6
24816
PE1, PE2 terminals
14 10 8
86
0.5 to 0.6 1.2 to 1.5 0.9
0.5 to 0.6 1.2 to 1.5 2
BR1 terminals
14 10 8 10
24
U1,V1,W1,U2,V2,W2,C,D
terminals
14 10
6
16
4
8
248
2
terminals not available
35
10
4
6
16
1.2 to 1.50.5 to 0.6
3
0.5 to 0.6
6
1.2 to 1.5
14 10
24
0.5 to 0.6 1.2 to 1.5
14
14
2
610
4
U1,V1,W1,U2,V2,W2,C,D
terminals
PE1, PE2 terminals
U1,V1,W1,U2,V2,W2,C,D
terminals
PE1, PE2 terminals
BR1 terminals
BR1 terminals
2
2
50
4 12 10-30
NOTE!
Use 60°C / 75°C (140°F / 167°F) copper conductor only.
The grounding conductor of the motor cable may conduct up to twice the value of the rated current if
there is a ground fault at the output of the AGy Drive.
Caution