50 • Chapter 5 - Wiring Procedure ARTDriveG Instruction manual
Table 5.7.2.1: Recommended Values for Output Chokes
Drive type
Mains
inductance
Rated
current
Saturation
current
Model
[mH] [A] [A]
abcD1E1
1007
1015
1022
1030
2040
2055
2075
3110
3150 0.43 32 68 LU3-015 S7FM2 7.5 (16.5) 180 (7.1) 160 (6.3) 170 (6.7) 150 (5.9)
70 (2.8)
4220
0.33 42 72
LU3-022 S7FH3 8 (17.6) 180 (7.1) 160 (6.3) 170 (6.3) 150 (5.9) 70 (2.8)
4300
0.24 58 100
LU3-030 S7FH4 9.5 (20.9) 180 (7.1) 160 (6.3) 180 (7.1) 150 (5.9) 80 (3.1)
4370
0.18 76 130
LU3-037 S7FH5 9.7 (21.4) 180 (7.1) 160 (6.3) 180 (7.1) 150 (5.9) 80 (3.1)
5450
5550
6750
7900
71100
71320
2002
2003
2005 1.9 7 13 LU3-5-005
S7FI3
2 (4.4) 120 (4.7) 125 (4.9) 75 (2.6) 100 (3.9)
42 (1.6)
3007
3010
3015
3020
4025
0.51 30 54.9
LU3-5-025
S7FI6
6.2 (13.7) 150 (5.9) 164 (6.4) 106 (4.2) 90 (3.5)
70 (2.8)
4030
0.43 36 65.9
LU3-5-030
S7FI7
6.8 (15) 180 (7.1) 182 (7.2) 122 (4.8) 150 (5.9)
64 (2.5)
4040
0.34 46 84.2
LU3-5-040
S7FI8
10 (22) 180 (7.1) 165 (6.5) 170 (6.7) 150 (5.9)
84 (3.3)
4050 0.27 58 106.1 LU3-5-050
S7FI9
12 (26.5) 180 (7.1) 165 (6.5) 170 (6.7) 150 (5.9)
84 (3.3)
5060 0.22 69 126.3 LU3-5-060
S7FL0
12 (26.5) 180 (7.1) 165 (6.5) 170 (6.7) 150 (5.9)
84 (3.3)
5075 0.18 86 157.4 LU3-5-075
S7FL1
12 (26.5) 180 (7.1) 165 (6.5) 170 (6.7) 150 (5.9)
84 (3.3)
6100 0.14 109 200 LU3-5-100
S7FL4
7125 0.11 158 290 LU3-5-150
S7FL5
7150 0.11 158 290 LU3-5-150
S7FL5
8200 0.070 220 403 LU3-5-200
S7FL6
agy0704
Three-phases choke
0.51 27 57
SIEI code
S7FG2
S7FG3
LU3-003
Weight
kg (lbs)
Dimensions : mm (inch)
0.12 110 192
540
0.07
310
S7FH7
S7FH8
0.87 16 34
LU3-011
LU3-005
S7FG4
S7FH6
310
AGy…-4 (230V…480V)
LU3-090
LU3-160
LU3-055
1.4 9.5 20
180
0.041
80 (3.1)
60 (2.4)
60 (2.4)
70 (2.8)
5.2 (11.5) 180 (7.1) 110 (4.3) 150 (5.9)170 (6.7)
110 (4.3)
180 (7.1)
170 (6.7)
180 (7.1) 130 (5.1)
150 (5.9)
150 (5.9)
14 (30.9) 240 (9.4) 210 (8.3) 180 (7.1) 200 (7.9)
8 (17.6)
180 (7.1)5.8 (12.8)
18.5 (40.8) 240 (9.4) 210 (8.3) 200 (7.9) 200 (7.9) 80 (3.1)
90 (3.5)250 (9.8)240 (9.4)260 (10.2)300 (11.8)27.5 (60.6)
75 (2.6) 100 (3.9)8.5
LU3-5-003
S7FI2 2 (4.4) 42 (1.6)
1 13,8 25.3
LU3-5-010
S7FI4 5 (11) 150 (5.9) 152 (6) 80 (3.1) 55 (2.2)
0.64 24,2 44.3
LU3-5-020
106 (4.2) 90 (3.5) 70 (2.8)S7FI5 6.2 (13.7) 150 (5.9) 164 (6.4)
AGy…-5 (575V)
120 (4.7) 125 (4.9)3 4.5
Please contact the nearest SIEI office
90 (3.5)
NOTE!
When the Drive is operated at the rated current and at 50 Hz, the output chokes cause a voltage drop
of approx. 2% of the output voltage.
5.7.3 Interference Suppression Filters
The inverters of AGy series must be equipped with an external EMI filter in order to reduce the radiofrequency emissions on
the mains line. The filter selection is depending on the drive size and the installation environment. For this purpose see the
“EMC Guidelines” instruction book.
In the Guide it is also indicated how to install the cabinet (connection of filter and mains reactors, cable shield, groundig,
etc.) in order to make it EMC compliant according the EMC Directive 89/336/EEC.
The document describes the present situation concerning the EMC standards and the compliance tests made on the SIEI
drives.
To Next Page
