How to troubleshoot Simrad AI50 when the unit will not switch on?
If your Simrad Transceiver unit won't switch on, there are a couple of things to check: * First, examine the power connection to ensure it's properly connected. * Second, check the fuse. If it has blown, replace it and then check the power supply.
What to do if my Simrad AI50 has no GPS position data?
If your Simrad Transceiver shows no GPS position data, the issue might be with the antenna or its cable. Check the antenna cable and its connections to ensure they are secure and functioning correctly.
Why is there no picture on my Simrad Transceiver display?
If there's no picture on the Simrad Transceiver display, try these steps: 1. Ensure the unit is powered up by pressing the PWR/ key. 2. Check the light level setting. If it's too low, increase it.
How to fix Simrad AI50 Transceiver when there is no AIS transmission?
If your Simrad Transceiver is not transmitting AIS data, there are two potential reasons: * The MMSI number might not be entered. Enter the MMSI number in the system. * The transmit function might be disabled. Enable transmit in the settings.
What causes no HDG info on Simrad AI50 Transceiver?
If your Simrad Transceiver is not displaying HDG information, it could be due to a SimNet cable problem. Check the SimNet power/connector to ensure it is properly connected and functioning.
Why is my Simrad AI50 Transceiver not logging data?
If your Simrad Transceiver is not logging data, consider the following: * Check if an SD card is installed. If not, install one. * Verify that the SD card is the correct type. If not, install the correct type of SD card.
How to enable mapping detail on Simrad AI50 Transceiver?
If your Simrad Transceiver is not showing mapping details, the coastline detail might not be active. Activate coastline detail in the settings.
General| Brand | Simrad |
|---|---|
| Model | AI50 |
| Category | Transceiver |
| Language | English |
Provides a general overview of the Simrad A150 Automatic Identification System (AIS).
Explains the structure and purpose of the manual for the AI50.
Details Simrad's proprietary high-speed data bus network with NMEA2000.
Discusses considerations for mounting the AI50 unit for optimal navigation.
Provides instructions and dimensions for flush mounting the AI50 unit onto a flat surface.
Details the procedure for mounting the AI50 unit using a supplied bracket.
Advises on the optimal placement and connection of the GPS antenna for accurate reception.
Guides on the proper installation and positioning of the VHF antenna for optimal performance.
Explains how to connect the power and data cables for the AI50 unit.
Describes the connection procedure for the SimNet databus cable.
Provides instructions for accessing and using the SD card slot on the AI50.
Illustrates the physical layout of the AI50 keypad and its components.
Explains the function of the PWR/Lights key for powering the unit on and off.
Details the operation of the 8-way NavPad for display, menu, and data entry modes.
Describes how to use the zoom keys to adjust the display range.
Explains the function of the ENTER/MENU key for navigating menus and confirming selections.
Details how to access vessel information and status updates using the INFO/STATUS key.
Explains the TRACK/CLR TRK key for tracking vessels and clearing trails.
Describes the HOME/DSC key for resetting view and initiating DSC calls.
Explains how to switch between different display views and access Text Mode.
Details how to adjust the display and keypad backlight using the PWR/* key.
Explains the color and content conventions used in AI50 display windows.
Outlines the steps and warnings shown when the AI50 is powered on for the first time.
Guides the user through the process of configuring vessel-specific information for the AI50.
Details the procedure for entering and confirming the vessel's MMSI number.
Explains how to select and enter the vessel type from a predefined list.
Guides on entering vessel dimensions and GPS reference data.
Provides instructions for entering the vessel's call sign.
Explains how to enter and store the vessel's name.
Introduces the AI50's user-configurable features accessible via the menu.
Explains how to adjust display settings to change the look and feel of the operation.
Describes how to toggle the coastline detail display on or off.
Details how to track the progress of the own vessel relative to other AIS vessels.
Explains how to offset the display to show a greater range in front of the vessel.
Guides on how to toggle the display of range rings on or off.
Covers settings related to the visual appearance of the display and keypad.
Details how to adjust the brightness of the display in 10% increments.
Explains how to adjust the brightness of the keypad backlighting.
Describes how to change the color of the keypad backlighting.
Guides on selecting display color palettes for different lighting conditions.
Explains how to add vessels to a Favourites List for easy access and alerts.
Details the process of adding a vessel to the Favourites List via MMSI and name.
Describes how to edit existing entries in the Favourites List.
Guides on how to remove entries from the Favourites List.
Covers the activation and setup of various safety alarms on the AI50.
Details how to set up CPA/TCPA and Guard Zone collision alarms.
Explains the calculation and setting of CPA/TCPA values for collision avoidance.
Describes how to set a perimeter around the vessel to detect approaching targets.
Explains the alarm that triggers when AIS reception from a vessel is lost.
Describes the alarm that notifies when a favourite vessel enters VHF range.
Covers customization options for AI50 functionality and settings.
Details how to change units for distance and speed measurements.
Explains how to apply an offset to display local time instead of UTC.
Guides on entering and editing vessel information like MMSI and name.
Describes how to toggle the sound made when a key is pressed.
Explains how to change the operating language of the AI50.
Covers enabling, disabling, and playing back recorded data.
Details the steps to enable data logging and select a file name.
Explains how to disable data logging and ensure data is saved.
Guides on selecting and replaying recorded voyage data.
Covers enabling or disabling the AI50's VHF transmitter.
Explains how to reset system variables to factory defaults.
Details options related to SimNet/NMEA2000 data sources and network management.
Guides on selecting a SimNet/NMEA2000 data source for heading information.
Covers managing device and system instances within the SimNet network.
Explains assigning unique device numbers to prevent network conflicts.
Details allocating unique numbers to networks for intercommunication.
Shows how to display all products connected to the SimNet/NMEA2000 network.
Explains enabling or disabling control of the AI50 by the WR20 Remote Commander.
Guides on selecting a DSC radio for initiating calls.
Displays unique identifier, software version, and ship configuration details.
Introduces the features and display elements of the AI50 Map Mode.
Explains the different icons used to represent vessel states and alarm conditions.
Describes the concentric range rings and how to read display range information.
Details the different view modes (NORTH UP, HEAD UP, COG UP) for map display.
Explains how to toggle coastline detail on or off for map orientation.
Describes the cursor's appearance and movement using the NavPad.
Explains the transmit legend's function and status indicators.
Covers viewing information for own and other vessels within VHF range.
Details how to view own vessel's information panel and its contents.
Explains how to get a summary of other vessels' information.
Guides on viewing comprehensive information for other vessels.
Describes how to display only the MMSI or name of other vessels.
Provides general rules for interpreting vessel information icons and dialogue boxes.
Details the procedure for initiating a DSC call to a vessel from map mode.
Explains how to enter and use the Text Mode for viewing vessel data.
Guides on changing the sort order of vessels displayed in Text Mode.
Refers to section 6.10 for making DSC calls from text mode.
Details how to select and track individual vessels on the map.
Explains how to enable and view tracking for your own vessel.
Guides on how to clear all displayed vessel trails.
Details a shortcut for adjusting display and keypad lighting levels.
Describes the types of visual alarms, alerts, and warning symbols used by the AI50.
Explains the CPA/TCPA collision alarm and its warning display.
Details the alarm for lost AIS transmissions from a vessel that triggered a collision alarm.
Describes the Level 2 alarm triggered when a vessel enters the defined guard zone.
Explains the Built-In Integrity Test (BIIT) alarm for detecting transceiver faults.
Details the Level 3 alarm activated when AIS reception from a vessel is lost.
Describes the alarm that sounds when a favourite vessel enters VHF range.
Explains the Level 3 alarm for lost compass heading data from SimNet/NMEA2000.
Details the Level 3 alarm for receiving safety messages from other vessels.
Provides instructions for cleaning and maintaining the AI50 unit.
Offers simple checks to resolve common issues before seeking technical assistance.
Lists optional accessories available for the AI50.
Presents detailed technical specifications for the AI50.
Shows the physical dimensions of the AI50 unit and its GPS antenna.
Advises on contacting dealers for repairs and warranty information.
Provides the EU Declaration of Conformity for the AI50.
To Next Page
