Why is my Simrad V5035 not transmitting AIS?
If your Simrad Transceiver isn't transmitting AIS, there might be several reasons. First, ensure that you have entered the MMSI number into the system. Second, check if the transmitter is disabled and enable it. Finally, verify that the power supply voltage is adequate, as a low voltage can prevent transmission.
What to do if my Simrad V5035 Transceiver has no GPS position data?
If your Simrad Transceiver isn't receiving GPS data, the issue likely stems from the antenna or cabling. You should check the antenna cable and its connections to ensure they are properly installed and functioning correctly.
How to fix a Simrad Transceiver that cannot power on?
If your Simrad Transceiver won't power on, begin by inspecting the power connection for any faults. Make sure the polarity is correct. Also, check the power supply to ensure it provides sufficient current.
Why is there no picture on my Simrad V5035 Transceiver display?
If there is no picture on the display of your Simrad Transceiver, first, ensure that the unit is powered up by pressing the power key. If it's on but the screen is dark, increase the dimmer level, as it might be set too low.
What causes a Simrad Transceiver to show no AIS target?
If your Simrad Transceiver isn't showing any AIS targets, it could be due to a problem with the VHF cabling. Check the antenna cable and connections to ensure they are properly installed and in good working order.
Why does my Simrad V5035 AIS range seem too low?
If the AIS range on your Simrad Transceiver seems too low, the issue is likely related to the VHF antenna and cabling. You should check the VHF antenna and cable installation to ensure they are correctly set up and functioning optimally.
How to show map detail on Simrad V5035 Transceiver?
If your Simrad Transceiver is not showing map details, make sure that the coastline detail is active by switching to coastline view.
What to do if sensor ports not response on Simrad V5035 Transceiver?
If the sensor ports on your Simrad Transceiver are not responding, the problem may be with the cable installation. Check the related wiring to ensure everything is properly connected.
General| Brand | Simrad |
|---|---|
| Model | V5035 |
| Category | Transceiver |
| Language | English |
Highlights critical safety warnings regarding electrical shock.
Covers safety warnings about power sources and water exposure.
Introduces the SIMRAD V5035 AIS Class A transponder.
Lists the key features of the V5035 AIS transponder.
Illustrates the system's connections and interfaces.
Lists all items included in the V5035 package.
Provides step-by-step instructions for installing the transponder.
Details the recommended placement and guidelines for VHF antenna installation.
Provides guidelines for optimal GPS antenna installation.
Offers guidelines for selecting an appropriate mounting location for the transponder.
Describes the process for panel mounting the transponder unit.
Illustrates the steps for mounting the junction box.
Details the initial setup and configuration steps for the V5035.
Identifies and describes the transponder's controls and display elements.
Details display modes, target symbols, and view options.
Displays detailed dynamic and static information about the user's ship.
Shows received AIS information of other vessels.
Lists current AIS alarms and their status.
Monitors vessels with insufficient CPA and TCPA.
Provides access to settings required during installation.
Details settings for call sign, name, type, and GPS antenna position.
Configures navigational information like destination, ETA, and cargo.
Allows setting Closest Point of Approach and Time to CPA for dangerous targets.
Enables setting the MMSI, IMO, and ENI numbers.
Allows switching AIS transmission on/off and GPS antenna voltage.
Provides access to user-configurable preferences for the V5035.
Sets baud rates for sensor ports and the USB port.
Restores the transponder to its original factory settings.
Enables changing user passwords for accessing protected sections.
Enables or disables ALR sentences for alarms.
Fine-adjusts VSWR threshold based on cable length and antenna characteristics.
Provides access to check system statuses like On/Off, Memory, and Ports.
Tests communication by sending and receiving specific AIS messages.
Details the technical specifications of the VHF transceiver.
Outlines the technical specifications for the DSC receiver.
Details the supply voltage and power consumption.
Shows front and side dimensions of the main transponder unit.
Guides through troubleshooting common issues with the transponder.
Explains how to define alarms for target proximity or loss.
Details alarms, their IDs, and the system's reaction to failures.
Provides a template for recording installation and maintenance details.
To Next Page
