SLE SLE1000 - Functional Testing

128 pages

Save Page as PDF

To Next Page

To Next Page

To Previous Page

To Previous Page

Loading...

Page 79 of 128

Functional Testing

Table of Contents

Default Chapter5
- Table of Contents5
1 Introduction10
- Device10
- Accessories and Generic Combination Devices11
- Intended Use11
- Intended Users11
2 SLE1000 Description14
3 Description of Symbols16
4 User/Owner Responsibility18
5 Warnings19
- Operational Warnings19
- Clinical Warnings22
6 User Interface24
- Main LCD Display24
- LED Display Windows24
- Push and Turn Knob25
- Audio Paused and Boost Buttons25
- Light Bar25
7 Operation26
- Power up26
- Oxygen Calibration Routine Description29
- Power down30
8 Standby Mode31
- Exiting Standby Mode31
9 Selecting a Parameter, Display or Calibration Function32
- Upper and Lower Level Functions32
- Upper Level Functions, Displays and Parameters37
- Showing Battery Charge Level39
- Alarm History42
- Set Flow44
- Elapsed Time Counter46
10 Audio Mute Button47
- Pre-Mute47
- Audio Paused48
11 Boost Button50
12 Indicators51
- Cycle Indicator Bargraph51
- Breath Detection51
- Averaged Value52
- Measured Values52
- Battery and Mains Indicators53
- Power Related Faults53
13 CPAP & Flow Mode56
- Standby to Flow Mode56
- Setting a Flow in Flow Mode58
- Flow Mode to CPAP Mode61
- Standby to CPAP Mode63
- CPAP to Flow Mode65
14 SLE1000 Set-Up70
- First Use70
- Rotation of Gas Inlets72
- Water Trap and Particulate Filter72
- Standard Setup73
- Disconnection of Air and Oxygen Hoses76
- Battery Charging77
- Battery Care77
- Using the SLE1000 on Battery Power77
- Mains Isolation78
- Extended Storage and Transportation78
15 Functional Testing Prior to Patient Use80
- Battery Test81
- Mains Disconnect Alarm81
- Total Power Fail Alarm Test82
- High Leak and High Pressure Alarm82
- Apnoea Alarm82
- Zero Pressure Alarm and Purge Check83
- Gas Supply Alarms83
16 Operational Considerations86
- General86
- Cpap86
17 Basic Operation88
- Monitoring88
- Operation88
18 Troubleshooting Chart90
Technical Information93
19 Cleaning and Disinfection94
- Preparation of a New SLE1000 CPAP Driver94
- Cleaning and Disinfection of an In-Service Driver94
- Cleaning Method95
- Disinfection Method95
20 Messages & Alarms96
- Messages96
- Alarm Messages and Sounds98
21 Technical Specification106
- Operating Mode106
- Monitoring106
- Indicators106
- Controls106
- Alarms107
- Outputs107
- Oxygen Sensor Life107
- Gas Supplies108
- Operating Environment108
- Power Requirements109
- Dimensions109
- Classification109
- Environmental Storage Conditions109
- Product Life Cycle109
22 Maintenance Schedule110
- SLE1000 Service Requirements110
- Preventative Maintenance111
23 EMC Compliance112
- Electromagnetic Immunity113
- Recommended Separation Distances between Portable and Mobile RF Communications Equipment and the SLE1000115
24 Rs232116
- RS232 Output Specification116
25 Pneumatic Unit Schematic SLE1000117
26 SLE1000 Overlay118
27 Equipment Checklist119
28 Consumables and Accessories122
29 Glossary of Abbreviations Used in this Manual124
30 Index125

Related product manuals

Preview: SLE SLE5000 Model J

SLE SLE5000 Model J

Preview: SLE 5000

Preview: SLE 2000