• [Cinema Conversion Mode]
You can set the video conversion method for
480p,
nop,
1080i, or 1080p* signals from the
HOMI OUT
jack
or the COMPONENT VIOEO
OUT jacks.
*
HDMlonly
[AutoJ: Normally select this. The unit
automatically detects whether the material is
video-based or film-based, and switches to the
appropriate conversion method.
[Video]: The conversion method suited for
video-based material will always be selected
regardless
of
the material.
• [Output Video Format]
You can select the
jack
type to output video
signals. For details, see "Video Output
Resolution" (page 104).
1 Press
"'I'"
to select the jack type to
output video signals, then press
().
mm
• When connecting the HDMI OUT
jack
and
other video outputjacks at the same time, select
[Component Video].
[TV
Connection
Method]
[HOMIJ: Outputs signals from the HOMI
OUT
jack according to the [HOMI
ResolutionJ setting below.
[Component Video): Outputs signals from
the COMPONENT VIOEO OUT jacks
according to the [Component Resolution]
setting below.
[VideoJ: Outputs signals from the VIOEO
OUT
jack.
2 (When you select [HOMI] or
[Component Video])
Press
"'I'"
to select the signal type for
the HOMI OUT jack or COMPONENT
VIDEO OUT jacks, then press
().
When you change the video output
resolution, a picture is displayed in the
selected resolution for about 30 seconds,
then the display asks for confirmation.
Follow the on-screen instructions.
"HO" lights up in the front panel display
when outputting
nop/
1080ill080p video
signals.
mm
• If the picture
is
distorted or no picture appears,
wait for about 30 seconds without pressing any
buttons. The display returns to the resolution
setting screen.
•
If
the selected video output resolution
is
incorrect, no picture appears on the screen when
you press any button
in
30 seconds.
In
this case,
press and hold
~
and
~
on the unit for more
than 5 seconds to reset the video output
resolution to the lowest resolution.
• When connecting the HDMI OUT jack and
other video outputjacks at the same time, video
signals may not output from thejacks, other than
from the HDMI OUT jack, when [Auto] or
[I 080p] is selected.
[HDMI
Resolution]/[Component
Resolution]
[Auto] (HOMI only): Normally select this.
The unit outputs signals starting from the
highest resolution acceptable to the TV:
1080p
> 1080i >
nop
> 480p > 480i
If
the resulting image format is undesirable,
try another setting that suits your TV.
[480iJ: Outputs 480i video signals.
[480pJ: Outputs 480p video signals.
[nopJ:
Outputs
nop
video signals.
[1080iJ: Outputs 1080i video signals.
[1080pJ (HDMI only): Outputs 1080p
video signals.
• [BO-ROM 1080/24p Output]
You can set to output 1920 x 1080p/24 Hz video
signals when playing film-based materials on
BO-ROMs
(nOp/24
Hz or 1080p/24 Hz).
1920 x 1080p/24 Hz video signals can be output
when all
of
the following conditions are met.
- You connect a 1080/24p-compatible TV
using the HOMI
OUT
jack,
- [Output Video FormatJ is set to [HOMl), and
- [HOMI ResolutionJ
is
set to [AutoJ
or
[1080p).
The 24P indicator lights up when outputting
1920 x 1080p124 Hz video signals.
[Auto
J:
Outputs 1920 x 1080p/24 Hz video
signals only when connecting a 1080124p-
compatible TV using the HOMI OUT jack.
[OnJ: Outputs 1920 x 1080p124 Hz video
signals regardless
of
the connected
TV
type.
-
81
US
To Next Page
Loading...
