Sony RCD-W10 Service Manual

79
RCD-W10
Pin No.
82
83
84
85
86
87
88, 89
90 to 93
94
95
96
97
98
99
100
101
102
103
104
105
106 to 108
109
110
111
112
113
114
115
116
117
118, 119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
I/O
—
—
—
—
—
—
I
O
I
I
O
I
O
O
I
I
I
O
—
—
O
I
I
I
I
I
I
I
—
—
O
—
—
O
O
O
O
O
O
I
O
O
I
I
I
O
O
I
O
—
Pin Name
DVDD
DVSS
DVDD
DVSS
AVDD
AVSS
SLCIST1, SLCIST2
SLCO0 to SLCO3
EFMIN
EFMIN2
DSLB
JITIN
JITC
RPO
OPP
PCKISTF
PCKISTP
PD0
AVDD
AVSS
PDS1 to PDS3
FR
AD0
RREC
FE
TE
VREF
AD1
AVDD
AVSS
DA0, DA1
DVDD
DVSS
DA2
TDO
FDO
SLDO
SPDO
SUBSYNC
ZRFDET
SHOCK
LOCK
DEF
HFL(MIRR)
TES
EFMO
LDON
FG
PCK2
DVDD
Description
Power supply +5V (digital)
Ground terminal (digital)
Power supply +3.3V (digital)
Ground terminal (digital)
Power supply +3.3V (analog) for slice level setting
Ground terminal (analog)
EFM slice level setting signal input
EFM slice level output
EFM signal input
EFM signal input Not used (open)
PWM signal output for SLC Not used (open)
Jitter judgement input
Jitter output
P/N balance adjustment terminal
P/N balance adjustment terminal
Charge pump terminal for the frequency comparison
Charge pump terminal for the phase comparison
Filter for the charge pump
Power supply +3.3V (analog) for the charge pump
Ground terminal (analog)
Charge pump selection terminal Not used (open)
VCO frequency setting input teminal
AD input
FOK signal input for optical judgement
Focus error signal input
Tracking error signal input
Servo system reference voltage input
AD input
Power supply +5V (analog) for the servo block AD/DA
Ground terminal (analog)
DA output Not used (open)
Power supply +3.3V (digital)
Ground terminal (digital)
DA output
Tracking signal output
Focus signal output
Sled signal output
Spindle signal output
Sub-code sync signal output
Judgement signal input for the existence of RF signal (fixed at “H”)
Shock detection signal output Not used (open)
PLL lock status signal output Not used (open)
Defect detection signal input
MIRR detection signal input
Tracking zero cross signal input
EFM signal output after formation of 2 values (open)
Laser control signal output for play back
Rotation monitor signal input from the spindle motor driver
Bit clock output for EFM playback
Power supply +5V (digital)

Sony RCD-W10 Specifications

Power

North American model power requirements	120 V AC, 60 Hz
Mexican model power requirements	120 V AC, 60 Hz
Other models power requirements	110-120/220-240V AC, 50/60 Hz
Power consumption	25 W

Inputs

ANALOG IN impedance	47 kilohms
ANALOG IN rated input	500 mVrms
ANALOG IN minimum input	250 mVrms

Outputs

ANALOG OUT impedance	47 kilohms
ANALOG OUT rated output	2 Vrms
ANALOG OUT load impedance	over 10 kilohms

Weight and Dimensions

dimensions	430 × 108 × 399 mm
RCD-W50C mass	6.8 kg
RCD-W10 mass	6.0 kg