SunStar SPS/A-3020 5030 SERIES - Inside Structure of Control Box

132 pages

To Next Page

To Previous Page

2) Inside Structure of Control Box

Floppy Disk

Driver

Power Board

Main Shaft Motor

Drive Board

Fan

Step Motor Drive Board

Trans

CPU+IO Board

Main Page

Table of Contents4
Machine Safety Regulations6
Machine Specifications9
Machine Specifications10
Names of Earch Part of the Machine10
Inside Structure of Control Box11
Machine Installation12
Machine Installation Conditions12
Electric Installation Conditions12
Assembly of Peripheral Components12
Preparation before Using the Machine15
Setting the Voltage15
How to Supply Oil16
How to Install the Needle Bar17
How to Pass Upper Thread18
Threading the Lower Thread18
How to Take the Bobbin Case on and off19
How to Adjust the Tension of the Upper Thread and the Lower Thread19
How to Wind the Lower Thread20
Adjusting the Height of the Presser Foot20
Disposing the Waste Oil20
How to Adjust Air Pressure21
How to Adjsut Rising and Descending Speed of the Upper Feed Plate21
How to Use Pallet22
How to Adjust Upper Thread Holding Device24
Caution When Using the Floppy Disks26
Basic Operational Method27
Name and Roles of each Key on Operation Unit27
Name and Description of each Display Contents on General Operation Mode28
Flow Chart of General Operation29
Work Flow of Pattern Programming30
Operating after Reading the Patterns from Floppy Disks31
Confirming the Working Pattern Read from the Floppy Disks31
When a Machine Stops Operating During Sewing by the Thread Cut32
Emergency Stop During Operation32
Winding the Thread32
Applicable Operation33
Operating after Moving to a Random Start Point to Sew or the Second Origin33
Program Example 1 : Generating the Square Pattern34
Program Example 2 : Generating the Circle Pattern36
Program Example 3 : Generating the Double Curve Pattern38
Program Example 4 : Pattern Generation by Using the Second Origin and Pause41
Program Example 5 : Change of Sewing Speed Within a Pattern45
6-1) Changing the Sewing Speed from an Existing Pattern Data45
6-2) Changing the Sewing Speed by Making New Pattern Data48
Using the Extension/Reduction Modes50
Using the Chain Sewing Mode51
Checking and Deleting the Pattern Number54
Making a Copy the Pattern to Another Number or Diskette55
Change of Parameter Related to General Sewing56
Initialization of Parameter Related to General Sewing57
System Program Update58
Confirmation for Version of System Program59
Operating Method of High Technology60
Understanding the Function of Machine Test60
It Is Able to Convert from Embroidery Design68
Description on Parameter Related to General Sewing Operation70
Ptn_Str_Pos71
Secnd_Org71
Org_To_Strt73
Rev_Org_Strt73
Up_Count74
Dn_Count74
Strt_Open79
Strt_Hold79
Open_Strt79
Open_Strt179
Open_Strt279
How to Repair the Machine103
Adjusting the Height of the Needle Bar103
Adjusting the Needle and the Shuttle103
Adjusting the Spring on the Upper Side of the Shuttle104
Height Adjustment of Feed Plate104
Adjustment of Presser Foot104
Adjustment of Presser Foot Related Parts106
Adjusting Accessories for Thread Delay106
Adjusting Parts for the Wiper108
Adjusting the Thread Trimming Accessories109
Adjusting the Main Thread Control Device112
Adjusting the Upper Thread Detecting Device112
Adjusting the Hand Pulley Device112
Adjusting the Winding Device113
Tension Adjustment of Driving Belt113
How to Set the Original Point of X-Y116
Upper/Lower Clamp Disassembly and Cassette Assembly117
Air System Circuit Diagram119
Exchanging the Fuse120
Cause of Break-Down and Troubleshooting121
Appendix123
Error List123
Parameter Number Related to General Sewing124
Air_Type124
Function No. Related Pattern Programming127
Pattern Chart129
Electronic Circult Diagram[Sps/A-5030-HS]130

SunStar SPS/A-3020 5030 SERIES - Inside Structure of Control Box

Table of Contents

Related product manuals