FCC Compliance Statement
CAUTION: Changes or modifications not expressly approved by Digital Security Controls could void your
authority to use this equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interfer-
ence in a residential installation. This equipment generates, uses and can radiate radio frequency energy and,
if not installed and used in accordance with the instructions, may cause harmful interference to radio commu-
nications. However, there is no guarantee that interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television reception, which can be determined by turn-
ing the equipment off and on, the user is encouraged to try to correct the interference by one or more of the
following measures:
Re-orient the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/television technician for help.
The user may find the following booklet prepared by the FCC useful: “How to Identify and Resolve Radio/
Television Interference Problems”. This booklet is available from the U.S. Government Printing Office,
Washington D.C. 20402, Stock # 004-000-00345-4.
Important Information
This equipment complies with Part 68 of the FCC Rules and the requirements adopted by the ACTA. On the
side of this equipment is a label that contains, among other information, a product identifier in the format
US:AAAEQ##TXXXX. If requested, this number must be provided to the Telephone Company.
Product identifier: US:1VDAL03BSYSTEMIII
USOC Jack: RJ-21X
Telephone Connection Requirements
A plug and jack used to connect this equipment to the premises wiring and telephone network must comply
with the applicable FCC Part 68 rules and requirements adopted by the ACTA. A compliant telephone cord
and modular plug is provided with this product. It is designed to be connected to a compatible modular jack
that is also compliant. See installation instructions for details.
Ringer Equivalence Number (REN) The REN is used to determine the number of devices that may be con-
nected to a telephone line. Excessive RENs on a telephone line may result in the devices not ringing in
response to an incoming call. In most but not all areas, the sum of RENs should not exceed five (5.0). To be
certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the
local Telephone Company. For products approved after July 23, 2001, the REN for this product is part of the
product identifier that has the format:
US: AAAEQ##TXXXX. The digits represented by ## are the REN without a decimal point (e.g., 03 is a REN
of 0.3). For earlier products, the REN is separately shown on the label.
Incidence of Harm If this equipment Sur-Gard SYSTEM III causes harm to the telephone network, the tele-
phone company will notify you in advance that temporary discontinuance of service may be required. But if
advance notice is not practical, the Telephone Company will notify the customer as soon as possible. Also,
you will be advised of your right to file a complaint with the FCC if you believe it is necessary.
Changes in Telephone Company Equipment or Facilities The Telephone Company may make changes in
its facilities, equipment, operations or procedures that could affect the operation of the equipment. If this hap-
pens the Telephone Company will provide advance notice in order for you to make necessary modifications to
maintain uninterrupted service.
Equipment Maintenance Facility If trouble is experienced with this equipment Sur-Gard SYSTEM III, for
repair or warranty information, please contact the facility indicated below. If the equipment is causing harm to
the telephone network, the Telephone Company may request that you disconnect the equipment until the
problem is solved. This equipment is of a type that is not intended to be repaired by the end user.
DSC c/o APL Logistics 757 Douglas Hill Rd Lithia Springs, GA 30122
Additional Information
Connection to party line service is subject to state tariffs. Contact the state public utility commission, public
service commission or corporation commission for information.
Alarm dialing equipment must be able to seize the telephone line and place a call in an emergency situation. It
must be able to do this even if other equipment (telephone, answering system, computer modem, etc.) already
has the telephone line in use. To do so, alarm dialing equipment must be connected to a properly installed
RJ31X jack that is electrically in series with and ahead of all other equipment attached to the same telephone
line. Proper installation is depicted in the figure below. If you have any questions concerning these instruc-
tions, you should consult your telephone company or a qualified installer about installing the RJ31X jack and
alarm dialing equipment for you.
Industry Canada Statement
IC: 160A-SYSTEM3
NOTICE: This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications. This is confirmed by the registration number. The abbreviation, IC, before the reg-
istration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met. It does not imply that Industry
Canada approved the equipment.
©2005 Digital Security Controls
Toronto, Canada • www.dsc.com
Sales: 1-888-888-7838
Tech. Support (Canada & USA): 1-800-503-5869
Printed in Canada
29034630R004
To Previous Page
Loading...
