211728 | v7.2
Contents
A Manufacturer....................................................................................................................................1
B Name of machines.............................................................................................................................1
C Declaration of Conformity ....................................................................................................................2
D General descriptions, dangers and warnings ............................................................................................3
D.1 Overview via pictograms on the inspection side of the unit ...............................................................3
D.1.1 Available pictograms and their placing on the units .............................................................3
D.1.2 Warnings about dangers ...............................................................................................6
D.1.3 Machine card with unique data on every unit.....................................................................7
D.2 Dimensions of the units ............................................................................................................7
E The control panel for the control system..................................................................................................8
F Drawings, diagrams, guides and instructions for the use, maintenance and repair .............................................8
G Employees in charge of operation/control/maintenance ............................................................................8
H Unintended use and misuse – inappropriate applications for the machine .......................................................8
H.1 Air handling unit in operation .....................................................................................................9
I Instructions for unloading and handling on site .........................................................................................9
I.1 Delivery types ........................................................................................................................9
I.2 Handling methods ...................................................................................................................9
I.3 Warnings ...............................................................................................................................9
I.4 Handling examples ................................................................................................................ 11
I.4.1 Handling sections which are delivered on pallets .............................................................. 11
I.4.2 Handling units/sections which are delivered on base frame ................................................ 12
I.4.3 Additional information ................................................................................................ 15
J Installation ...................................................................................................................................... 16
J.1 Installation - mechanical ......................................................................................................... 16
J.1.1 Free area in front of and above the unit .......................................................................... 16
J.1.2 Supporting surface..................................................................................................... 16
J.1.3 Adjustable feet under legs or base frame and transport of sections....................................... 16
J.1.4 Base frame assembly ................................................................................................. 16
J.1.5 Base frames for outdoor units ...................................................................................... 17
J.1.6 Outdoor units — support under the base frame of the unit .................................................. 17
J.1.7 Installation on the site of unit sections at the base frame when sections are delivered on
pallets..................................................................................................................... 17
J.1.8 Joining the unit sections .............................................................................................. 19
J.1.9 Fitting the ductwork ................................................................................................... 20
J.1.10 Risk of stack effect by vertical ducts and wind pressure on louvers ....................................... 20
J.1.11 Door alignment ......................................................................................................... 21
J.1.12 Lock the doors by using the key.................................................................................... 21
J.2 Installation - electrical ............................................................................................................ 22
J.2.1 Installation of cable sealing boxes (only in rotor sections of Geniox GO 27—31)....................... 22
J.3 Installation – Pipes for water – hot and chilled, valves and drains ...................................................... 22
J.3.1 Description............................................................................................................... 22
J.3.2 Pipe connections ....................................................................................................... 22
J.3.3 Possibility of extracting components from the unit ............................................................ 23
J.3.4 Pipe connections to batteries ....................................................................................... 23
J.3.5 Draining condensate water .......................................................................................... 24
J.3.6 Draining condensate water from plate heat exchanger....................................................... 25
J.3.7 Draining condensate water from cooling battery............................................................... 25
K Installation and assembly instructions for reduction of noise and vibration emissions ...................................... 26
L Start-up, adjustments, use and commissioning........................................................................................ 26
L.1 Print-outs on paper ................................................................................................................ 26
L.2 Start-up by installer ............................................................................................................... 26
L.2.1 Remove rotor lock plate.............................................................................................. 27
L.2.2 Checklist, relevant values ............................................................................................ 27
L.3 Description of functions .......................................................................................................... 28
L.4 Commissioning ..................................................................................................................... 28
M Information about the residual risks .................................................................................................... 28
M.1 Unit casing ........................................................................................................................... 28
M.1.1 Design of the machine to make transport safe ................................................................. 28
To Next Page
Loading...
