TOP 600 XTPRO: Service & Maintenance Manual - rev. 2.0
Page ii
7.7.
D
ISASSEMBLING THE CARDIO RECEIVER
...........................................................................................................7.7
7.8.
D
ISASSEMBLING THE ELECTRONIC CIRCUIT BOARDS
.........................................................................................7.8
7.9.
D
ISASSEMBLING THE ALTERNATOR
..................................................................................................................7.9
7.10.
D
ISASSEMBLING THE BELT
.............................................................................................................................7.10
7.11.
D
ISASSEMBLING THE CHAIN
...........................................................................................................................7.12
7.12.
D
ISASSEMBLING THE PULLEY
.........................................................................................................................7.13
7.13.
D
ISASSEMBLING THE PRIMARY SHAFT
............................................................................................................7.14
7.14.
D
ISASSEMBLING THE SADDLE AND STEM GUARD
............................................................................................7.15
7.15.
D
ISASSEMBLING THE HANDLES
.......................................................................................................................7.16
7.16.
D
ISASSEMBLING THE ALTERNATOR BRUSHES
.................................................................................................7.17
8.
ADJUSTMENTS....................................................................................................................................................8.1
8.1.
B
ELT ALIGNMENT
.............................................................................................................................................8.1
8.2.
B
ELT TENSION
..................................................................................................................................................8.2
8.3.
C
HAIN ALIGNMENT
...........................................................................................................................................8.3
8.4.
C
HAIN TENSION
................................................................................................................................................8.4
8.5.
P
LAY OF SADDLE STEM
.....................................................................................................................................8.5
8.6.
W
EAR OF BRUSHES
...........................................................................................................................................8.6
9.
CONFIGURING THE MACHINE......................................................................................................................9.1
9.1.
U
SER SETTING PARAMETERS
.............................................................................................................................9.1
9.1.1.
Language used ..................................................................................................................................9.1
9.1.2.
Measurement system .........................................................................................................................9.1
9.1.3.
Maximum time...................................................................................................................................9.2
9.1.4.
Activating the “+” and “
−
” keys......................................................................................................9.2
9.1.5.
Disabling the function keys...............................................................................................................9.2
9.1.6.
Enabling the “ENTER” key..............................................................................................................9.3
9.1.7.
Setting the priority ............................................................................................................................9.3
9.2.
T
ECHNICAL SETTING PARAMETERS
...................................................................................................................9.3
9.2.1.
Enabling use of the hand sensor ....................................................................................................... 9.3
9.2.2.
Enabling the display mode................................................................................................................9.4
9.3.
M
AINTENANCE INFORMATION
..........................................................................................................................9.4
9.3.1.
Hours on ...........................................................................................................................................9.4
9.3.2.
Hours of use...................................................................................................................................... 9.4
9.4.
C
HANGING THE MAINTENANCE INFORMATION
..................................................................................................9.5
9.4.1.
Hours on ...........................................................................................................................................9.5
9.4.2.
Hours of use...................................................................................................................................... 9.5
10.
SCHEDULED MAINTENANCE.......................................................................................................................10.1
10.1.
E
XTERNAL CLEANING OPERATIONS
................................................................................................................10.1
10.1.1.
Setting up the operation ..................................................................................................................10.1
10.1.2.
Cleaning operations ........................................................................................................................10.1
10.2.
R
OUTINE MAINTENANCE OPERATIONS
............................................................................................................10.2
10.2.1.
Setting up the operation ..................................................................................................................10.2
10.2.2.
Cleaning operations ........................................................................................................................10.2
10.3.
S
PECIAL MAINTENANCE OPERATIONS
.............................................................................................................10.3
10.3.1.
Setting up the operation ..................................................................................................................10.3
10.3.2.
Checking the working conditions ....................................................................................................10.3
10.3.3.
Performing the routine maintenance procedure .............................................................................10.3
10.3.4.
Checking the wiring and connections.............................................................................................. 10.3
10.3.5.
Checking the display .......................................................................................................................10.3
10.3.6.
Checking the state of wear of the chain...........................................................................................10.4
10.3.7.
Lubrication......................................................................................................................................10.4
10.3.8.
Checking the state of wear of the alternator belt ............................................................................10.4
10.3.9.
Checking the play of the saddle stem ..............................................................................................10.4
10.3.10.
Checking the operation of the cardio receiver................................................................................10.4
10.3.11.
Checking the resistance setting ....................................................................................................... 10.4
10.3.12.
Checking the noise of the brushes ...................................................................................................10.4
To Next Page
Loading...
