Terex Genie GS-1330m Maintenance Manual

November 2021 Maintenance Manual
Introduction
Part No. 1305686GT Scissor Lifts iii
Models included in this manual
Use the following chart to identify the specific
serial number for models included in this manual.
Models
Serial number
GS
-1330m
from GS30MD
-101
GS
-1432m / 1932m
GS
-1932m Lite
GS
-1932m XH
from GS32MD
-101
from GS32MP
-101
GS-1530 / 1532
GS
-1930 / 1932
GS
-1932 XH
from GS30D-40101
from GS30P
-200101
GS
-2032 / 2632 / 3232
from GS32D-10101
from GS32P
-200101
GS
-2046 / 2646 / 3246
GS
-2646 XH / 3246 XH
GS
-4046
from GS46D
-40101
from GS46P
-200101
GS
-4655
from GS55D
-101
from GS55P
-101
GS
-2669 / 3369 / 4069 RT
GS
-2669 / 3369 / 4069 DC
GS
-2669 / 3369 / 4069 BE
from GS69F
-18000
from GS69M
-101
GS
-3384
from GS84D
-401
from GS84F
-46000
GS
-3390 / 4390 / 5390
from GS90D
-3201
from GS90F
-56000
Find additional Manuals for your
Model
Go to http://www.genielift.com
Use the links to locate Service Manuals,
Maintenance Manuals, Service and Repair
Manuals, Parts Manuals and Operator's Manuals.
Identifying the Correct Procedure
for your Model
Unless otherwise noted, each procedure will apply
to all models. Procedures that only apply to
specific models or options will include the
information in the procedure title.
Examples of procedures that apply to specific
models:
• Test the Oscillate Axle - GS-90
• Grease the Steer Yokes - GS-30, GS-32,
GS-46
• Model Abbreviations:
GS-30m: GS-1330m
GS-32m: GS-1432m, GS-1932m,
GS-1932m Lite, GS-1932m XH
GS-30: GS-1530, GS-1532, GS-1930,
GS-1932, GS-1932 XH
GS-32: GS-2032, GS-2632, GS-3232
GS-46: GS-2046, GS-2646, GS-2646 XH,
GS-3246, GS-3246 XH, GS-4046
GS-55: GS-4655
GS-69: GS-2669, GS-3369, GS-4069
(includes DC and RT models)
GS-84: GS-3384
GS-90: GS-3390, GS-4390, GS-5390
Examples of procedures that apply to all models:
• Test the Drive Speed – Stowed Position
• Inspect the Electrical Wiring
Glossary of terms:
ECM - Electronic Control Module
GCON - Ground Controller. This ECM is located at
the ground controls.
PCON - Platform Controller. This ECM is located
at the platform controls.
CAT5 Cable - Standard Ethernet cable used for
networking purposes.

Terex Genie GS-1330m Specifications

General

Brand	Terex
Model	Genie GS-1330m
Category	Lifting Systems
Language	English