CAUTION: Your device might open or close during
programming. Therefore, before programming,
make sure that the device is clear of any people or
objects.
2. Check that the device's remote control has a healthy
battery. Tesla recommends replacing the battery in the
device's remote control before Programming HomeLink.
3. Touch the HomeLink icon at the top of the Controls
screen.
4.
Touch Create HomeLink.
5.
On the HomeLink screen, enter a name for the device,
then touch Enter or Add New HomeLink.
6.
Choose the mode you wish to use (Standard, D-Mode, or
UR-Mode), then touch
Set Mode.
7.
Touch Start and follow the onscreen instructions.
NOTE: If you see a screen called “Train the receiver” while
programming the device, remember that this is a time-
sensitive step. After pressing the Learn/Program/Smart
button on the device's remote control, you have only
approximately 30 seconds to return to your vehicle and
press
Continue, and then press the trained HomeLink
device name twice. Consider having an assistant to
ensure you can complete this step within 30 seconds.
8. Once your device is programmed, touch Save to complete
the programming.
9. Ensure HomeLink works as expected. In some cases, you
may need to repeat the programming process multiple
times before succeeding.
Once programmed, you can operate the device by touching
its corresponding HomeLink icon on the touchscreen.
HomeLink remembers the location of your programmed
devices. When you approach a known location, the HomeLink
control on the touchscreen automatically appears. When you
drive away, it disappears.
NOTE: The HomeLink icon displays at the top of the
touchscreen when Model Y detects a programmed HomeLink
device within range, and the touchscreen is not already
displaying the HomeLink screen or popup,
NOTE: For additional assistance or compatibility questions,
contact HomeLink (www.homelink.com or call
1-800-355-3515).
Auto Opening and Closing
To operate a HomeLink device without using the
touchscreen, you can automate the device to open as you
approach, and close as you drive away:
1.
Touch the HomeLink icon at the top of the Controls
screen, touch HomeLink Settings, then choose the device
you want to automate.
2.
Adjust the device's HomeLink settings as needed:
◦
Select the Auto-open when arriving checkbox if you
want the device to open as you approach.
◦ Touch the arrows to specify the distance you want
Model Y to be from the device before it opens.
◦ Select the Auto-close when leaving checkbox if you
want the device to close as you drive away.
◦
Select the Auto-fold mirrors checkbox if you want
mirrors to fold when you arrive at the HomeLink
location. This is useful for narrow garages.
◦
Select the Chime for Auto-open and Auto-close
checkbox if you want Model Y to sound a chime when
a signal has been sent to open or close the device.
HomeLink remembers the vehicle’s GPS location at the time
of pairing and uses this to determine the vehicle’s
whereabouts in relation to the HomeLink device. HomeLink
does not detect and differentiate between opening and
closing (ex: if Auto-open is triggered and the door is already
open, the door will close) but typically determines whether to
auto-open or -close based on the following:
Auto-Open: Detects when Model Y approaches the garage
door (or other HomeLink device) within a specified distance.
Auto-open initiates so long as the approaching vehicle is in
Drive and HomeLink is enabled. HomeLink does not trigger
when the vehicle is already in the area.
Auto-Close: HomeLink triggers when the Model Y shifts from
Park into Reverse, and moves at least seven meters in
Reverse.
NOTE: Changing gears multiple times while in the specified
distance may interfere with Auto-close.
In situations where you don't want the device to automatically
open or close, touch
Skip Auto-Open or Skip Auto-Close at
any time during the count-down message.
NOTE: Do not rely on HomeLink to ensure the device fully
closes.
Resetting the Location of the HomeLink
Device
If you experience situations in which you sometimes drive up
to your HomeLink device and it doesn't open, or the
touchscreen does not display a notification as you approach
a programmed device, you may need to reset the device's
location. To do so, park as close as possible to the HomeLink
device (garage door, gate, etc.) and display the HomeLink
settings page by touching the HomeLink icon at the top of
the
Controls screen. Touch the name of the device you want
to reset, then touch Reset Location.
Deleting a Device
To delete a HomeLink device, touch the HomeLink icon at the
top of the
Controls screen, then touch HomeLink Settings.
Touch the name of the device you want to delete, then touch
Delete.
Smart Garage
64 MODEL Y Owner's Manual
To Next Page
Loading...
