EasyManuals Logo

Thytronic NV10P User Manual

Thytronic NV10P
240 pages
To Next Page IconTo Next Page
To Next Page IconTo Next Page
To Previous Page IconTo Previous Page
To Previous Page IconTo Previous Page
Page #23 background imageLoading...
Page #23 background image
23
NV10P - Manual - 01 - 2015
TECHNICAL DATA
3.8 CONTROL AND MONITORING
Frequency tracking
Locking range
[1]
20...63 Hz
Rate (instantaneous change) 5 Hz/s
Minimum voltage 0.015 E
n
Trip Circuit Supervision - 74TCS
Operate time:
One binary input supervision 40 s
Two binary inputs supervision 2 s
Reset time delay:
One binary input supervision 6 s
Two binary inputs supervision 0.6 s
Circuit Breaker supervision
Circuit breaker diagnostic
Number of CB trips threshold (N.Open) 0...10000
(step 1)
Circuit Breaker maximum allowed opening time (t
break
>) 0.05...1.00 s (step 0.01 s)
Oscillography (DFR)
[2]
Format
COMTRADE
Recording mode
circular
Sampling rate
24 samples / cycle
Trigger setup:
Pre-trigger time
0.05...1.00 s (step 0.01 s)
Post-trigger time
0.05...60.00 s (step 0.05 s)
Set sample channels:
u
L1
, u
L2
, u
L3
, u
E
Set analog channels:
Analog 1...Analog 12 f, U
L1
, U
L2
, U
L3
, U
E
, U
EC
, U
1
, U
2
,
df/dt
T1...T8
[3]
Set digital channels:
Digital 1...Digital 12 K1... K6, K7...K10,
IN1, IN2, IN3...IN42
[4]
PLC (Programmable Logic Controller)
[5]
Reference standard IEC 61131-3
Language
[6]
IL (Instruction List)
Inputs:
Binary inputs IN1, IN2 on board
IN8...IN10 with MRI module
IN11...IN26 with one MID16 module
IN27...IN42 with two MID16 modules
Delayed binary inputs
[7]
IN1, IN2 on board
IN8...IN10 with MRI module
IN11...IN26 with one MID16 module
IN27...IN42 with two MID16 modules
Start (all elements) Start U<, Start U<<,...etc
Trip (all elements) Trip U<, Trip U<<,...etc
Measures UL1, UL2,...ecc
Temperature Pt100
Outputs:
Relays K11...K6 on board
K7...K10 with MRI module
LEDs START, TRIP, L1...L6 on board
L7...L10 with MRI module
Current converter DAC
Note 1 If the measured frequency is out of the locking range, the system lock on to the rated frequency (50 or 60 Hz)
Note 2 For the DFR function a licence is required; call Thytronic for purchasing.
Note 3 The measures of temperature are available only when the MPT module on Thybus is enabled (eigth Pt100 inputs)
Note 4 Output relay K7...K10 and binary input IN3...IN42 states are available only when the concerning I/O circuits are implemented (MRI and MID16
modules on Thybus)
Note 5 For the PLC function a licence is required; call Thytronic for purchasing.
Note6 With ThySetter V3.4.3 release and compiler IEC 61131-3 V1.2.7 only the IL language is implemented (Instruction List);
other languages, according with IEC 61131 standard (ST (Structured Text)), LD (Ladder Diagram), FBD (Function Block Diagram), SFC (Sequential
Functional Chart), will be available soon
Note 7 The input state is acquired downstream the tON and tOFF timers

Table of Contents

Questions and Answers:

Question and Answer IconNeed help?

Do you have a question about the Thytronic NV10P and is the answer not in the manual?

Thytronic NV10P Specifications

General IconGeneral
BrandThytronic
ModelNV10P
CategoryRelays
LanguageEnglish

Related product manuals