What to do if WAREMA Control Unit cannot be found by the app?
If the WAREMA climatronic® WebControl cannot be found by the app, ensure that your Android device is connected to your router's WLAN network. Activate your router and ensure WLAN is enabled, then log into the WLAN network before opening the app.
Why I am unable to connect to my WAREMA Control Unit from my device?
If you are unable to connect to your WAREMA climatronic® WebControl from your PC or smartphone, it might be because the maximum number of browser connections has been reached. The WAREMA climatronic® WebControl allows access from a maximum of three browsers simultaneously. Ensure that no more than three devices are attempting to access the system at the same time.
How to fix WAREMA Control Unit IP address not recognized after power failure?
If the IP address of your WAREMA climatronic® WebControl is no longer recognized by the browser after a power failure, and DHCP is set to "ON", you will need to enter the new IP address. This can be found in the client table of your router. To prevent this in the future, set DHCP to "OFF".
What to do if WAREMA Control Unit app shows "No connection to WebControl"?
If you receive a "No connection to WebControl" error message in your WAREMA climatronic® WebControl App, it indicates an unstable WLAN connection between the app and the WAREMA climatronic® WebControl. To resolve this, establish a stable WLAN connection.
What to do if WAREMA Control Unit not found and LED flashes red?
If the WAREMA climatronic® WebControl is not found by the mobile device and the status LED flashes red, it could be because DHCP is set to "OFF". Check the network connection and verify the DHCP setting in the saved IP information if you're using an SD card. Set DHCP to "ON" if necessary. If you're using the Android app, find the IP address on the "System" tab and enter it in your browser's menu line, then save it as a bookmark.
Why green LED on WAREMA Control Unit RJ45 socket is not lit?
If the green LED on the RJ45 socket for the LAN cable is not lit, there may be a problem with the connection between the RJ45 socket and the router. Check the router's power supply and the connection between the router and the RJ45 socket.
What to do if WAREMA climatronic WebControl Control Unit status LED does not light up?
If the status LED on your WAREMA climatronic® WebControl does not light up, it indicates that the power supply has been interrupted. Check the connection at the yellow/white socket (power supply) or briefly press the reset button.
How to fix WAREMA climatronic WebControl page display in Internet Explorer?
If you're using Internet Explorer and the page isn't displaying correctly, with elements overlapping, it's likely due to Internet Explorer using the wrong view. Press the F12 key and set the browser mode to Internet Explorer 10.
Why WAREMA climatronic WebControl Control Unit cannot be operated over the Internet?
The WAREMA climatronic® WebControl is designed for use within your own WLAN network. Operate the WAREMA climatronic® WebControl from home on your WLAN network.
What to do if unable to add room in WAREMA climatronic WebControl Control Unit?
If you are unable to add an additional room and a plus does not appear next to "Room", it means you have reached the maximum capacity. Delete unnecessary rooms to create space for new ones.
Visual guides illustrating the physical setup and electrical connections.
Guide to setting up rooms, channels, groups, and scenes.
Instructions for controlling sun shading products and other connected devices.
How to connect to and operate the system via a web browser.
Detailed steps for configuring the system's structure.
Adjusting device positions like inclination and open/close percentage.
Using pre-programmed scenes to control multiple devices at once.
Instructions for setting IP addresses manually when DHCP is OFF.
Step-by-step solutions for frequent problems encountered during use.
General| Mounting | DIN rail |
|---|---|
| Power Supply | 24 V DC |
| Protection Class | IP20 |
| Product Type | Control Unit |
| Compatibility | WAREMA products |
| App Control | Yes |
| User Interface | Web interface |
| Weight | 200 g |
| Storage Temperature | -20°C to +70°C |
To Next Page
