What to do if F9E1 (drain pump system error) appears on my Whirlpool WFW94HEX Washer display?
If the error code F9E1 appears, indicating a drain pump system error, check the plumbing to ensure the drain hose is correctly installed. Also, lower the drain hose if its end extends into the standpipe farther than 4.5" (114 mm) or if it's higher than 96" (2.4 m).
What to do if F5E2 (door will not lock) appears on my Whirlpool WFW94HEX Washer display?
If the error code F5E2 appears, indicating the door will not lock, make sure the washer door is closed completely and properly latched.
Why is my Whirlpool WFW94HEX not draining/spinning, and the loads are still wet?
If your Whirlpool Washer is not draining or spinning, and the loads are still wet with the door locked at the end of the wash cycle, consider the following possibilities: * A tightly packed or unbalanced load may prevent correct spinning. * Using regular detergent or too much HE detergent can slow or stop draining or spinning. * The load may be out of balance. Balance a single item such as a rug or jeans jacket with a few extra items. * Check the plumbing for correct drain hose installation. * The drain hose might extend too far into the standpipe. Lower the drain hose if the end is higher than 96" (2.4 m).
What does F8E1 (water supply error) mean on my Whirlpool WFW94HEX Washer?
If the error code F8E1 appears, indicating a water supply error, check to ensure that the hot and cold inlet hoses are not reversed.
What to do if an error code appears on my Whirlpool WFW94HEX Washer display?
If an error code appears on the display, correct any possible issues, then press START/PAUSE once to clear the code. Press START/PAUSE again to restart the washer. If the code reappears, it may be necessary to call for service.
What to do if 'Sud' (excess suds) appears on my Whirlpool WFW94HEX Washer display?
If the error code 'Sud' appears, it indicates excessive suds in the washer. Allow the machine to continue its cycle. Make sure you're only using HE detergent and always measure the detergent based on the load size, following the detergent manufacturer’s instructions.
Why is my Whirlpool WFW94HEX Washer not performing correctly?
If your Whirlpool Washer is not performing as expected, make sure to add the load loosely, ensuring items can move freely to reduce wrinkling and tangling. Use only HE detergent, measuring it according to the manufacturer’s directions based on load size and soil level. If you're using liquid fabric softener, add it to the fabric softener compartment instead of using a dispensing ball.
Why is warm selection not available and the load not rinsed on my Whirlpool WFW94HEX Washer?
If your Whirlpool Washer warm selection is not available or the load is not rinsed, use only HE detergent, measuring it according to the manufacturer’s directions based on load size and soil level. Avoid tightly packing the washer. Use hot or warm washes if safe for the load. Check that the inlet valve screens are not clogged.
Explains the safety alert symbol and the meaning of DANGER and WARNING messages.
Covers electrical safety, grounding, and initial installation steps.
Lists common washer problems and their potential causes and solutions.
Explains error codes displayed by the washer and recommended procedures.
Initial checks, diagnostic mode entry, and testing procedures overview.
Detailed table of quick diagnostic tests for various components.
Tests for Cycle Control Unit power and interference filter.
Testing procedures for the user interface and motor circuit.
Procedure for checking the functionality of the door lock system.
Tests for the drum light and water inlet valves.
Procedure for testing the pressure sensor and switch.
Tests for the drain pump and flow meter.
Tests for the heating element and temperature sensor.
Procedure for testing the washer's dispenser system.
Safety guidelines for performing voltage measurements.
Table of common problems, causes, and checks for the washer.
Explanation and recommended procedures for fault/error codes.
To Next Page
General