VX-6E OPERATING MANUAL90
SET
(
MENU
)
M
ODE
SET MODE ITEM
4 [ARS]
51 [RPT]
56 [SHIFT]
SET MODE ITEM
8 [BELL]
17 [DCS CD]
18 [DCS RV]
21 [DT A/M]
22 [DT SET]
59 [SQL]
60 [SQL.TYP]
66 [TN FRQ]
SET MODE ITEM
2 [AR BEP]
3 [AR INT]
14 [CW ID]
SET MODE ITEM
10 [BNK NM]
20 [DMR.WRT]
38 [MW MD]
39 [NAME]
40 [NM SET]
SET MODE ITEM
49 [RESUME]
55 [SCN.LMP]
57 [SKIP]
73 [WX ALT]
68 [TS MUT]
69 [TS SPD]
SET MODE ITEM
53 [RXSAVE]
70 [TXSAVE]
72 [WAKEUP]
SET MODE ITEM
29 [INT CD]
30 [INT MD]
31 [INT.A/M]
32 [INT.SET]
SET MODE ITEM
23 [EAI]
24 [EAI.TMR]
26 [EMG S]
SET MODE ITEM
43 [PAGER]
44 [PAG.ABK]
45 [PAG.CDR]
46 [PAG.CDT]
AVAILABLE VALUES
(
DEFAULT
)
ON / OFF
SIMP / –RPT / +RPT
0.00 - 149.95 MHz
Ú1
AVAILABLE VALUES
(
DEFAULT
)
OFF / 1 / 3 / 5 / 8 /
CONT (Continuous ringing)
104 standard DCS codes (023)
DISABLE / ENABLE
MANUAL / AUTO
---
LVL 0 - LVL 15 (NFM: LVL 1),
LVL 0 - LVL 8 (WFM: LVL 2)
OFF / TONE / T SQL /
DCS / RV TN
50 standard CTCSS tones (100 Hz)
AVAILABLE VALUES
(
DEFAULT
)
IN RNG / ALWAYS / OFF
25 SEC / 15 SEC
--
AVAILABLE VALUES
(
DEFAULT
)
--
ON / OFF
NEXT / LOWER
FREQ / ALPHA
--
AVAILABLE VALUES
(
DEFAULT
)
3SEC / 5SEC / 10SEC /
BUSY / HOLD
ON / OFF
OFF / SKIP / ONLY
OFF / ON
ON / OFF
FAST / SLOW
AVAILABLE VALUES
(
DEFAULT
)
200 MS / 300 MS / 500 MS /
1 S / 2 S / OFF
OFF / ON
OFF / 5S / 10S / 20S / 30S / EAI
AVAILABLE VALUES
(
DEFAULT
)
DTMF 1 - DTMF F
SRG / FRG
MANUAL / AUTO
--
AVAILABLE VALUES
(
DEFAULT
)
OFF / ON
INT. 1M through INT.10M,
INT.15M, INT.20M, INT.30M,
INT.40M, INT. 50M,
CON. 1M through CON.10M,
CON.15M, CON.20M, CON.30M,
CON.40M, and CON. 50M
(CON. 5M)
BP+STR / BEAM / BP+BEM / CW /
BP+CW / BEEP / STROBE
AVAILABLE VALUES
(
DEFAULT
)
OFF / ON
OFF / ON
(05
_
47)
(05
_
47)
REPEATER SETTING
Enables/Disables the Automatic Repeater Shift function.
Sets the Repeater Shift Direction.
Sets the magnitude of the repeater Shift.
CTCSS/DCS SETTING
Selects the number of CTCSS/DCS Bell ringer repetitions.
Setting of the DCS code.
Enables/Disables "Inverted" DCS code decoding.
Enables/Disables the DTMF Autodial feature.
Programming of the DTMF Autodialer.
Sets the Squelch threshold level.
Selects the Tone Encoder and/or Decoder mode.
Setting of the CTCSS Tone Frequency.
ARTS SETTING
Selects the Beep option during ARTS operation.
Selects the Polling Interval during ARTS operation.
Programs and activates the CW Identifier.
MEMORY SETTING
Stores Alpha-Numeric “Tags” for the Memory Group.
Enables/Disables over-written the Direct Memory Recall Channel while operating on the Direct
Memory Recall Channel.
Selects the method of selection of channels for Memory Storage.
Toggles the display indication between “Frequency” and the channel's "Alpha/Numeric Tag."
Stores Alpha-Numeric "Tags" for the Memory channels.
SCAN SETTING
Selects the Scan Resume mode.
Enables/Disables the Scan lamp while paused.
Selects the Memory Scan “Skip•Echannel-selection mode.
Enables/Disables the Weather Alert Scan feature.
Enables/Disables the receiver audio output during the Tone Serch Scanner is activated.
Selects the Tone Serch Scanner speed.
POWER SAVING SETTING
Selects the Receive-mode Battery Saver interval.
Enables/Disables the Transmitter Battery Saver.
Setting of the Wakeup feature.
WIRES
TM
SETTING
Selects the Access Number (DTMF digit) for WIRES
TM
operation.
Selects the Internet Link Connection mode.
Enables/Disables DTMF Autodialer feature while operating on the Internet Connection feature.
Selects the memory register for an Access Number (DTMF code) for non-WIRES
TM
Internet
Link System access.
EAI SETTING
Enables/Disables the Emergency Automatic ID (EAI) Feature.
Setting of the Emergency Automatic ID (EAI) operating mode and its Transmit Time.
Selects the alarm(s) utilized when the Emergency function is engaged.
EPCS SETTING
Enables/disables the Enhanced CTCSS Paging & Code Squelch function.
Enables/disables the Answer Back function of the Enhanced CTCSS Paging & Code Squelch.
Setting the Receiver Pager Code for the Enhanced CTCSS Paging & Code Squelch.
Setting the Transmitting Pager Code for the Enhanced CTCSS Paging & Code Squelch.
Ú
1: Depends on the frequency band.
To Next Page
